KTMFLASH VAG DQ200 and DQ250 User Manual

KTMFlASH ECU flasher supports VAG DQ200 DQ250 DQ500 VL381 DL501 Direct-shift gearbox Transmission read and write via OBD or boot mode.

Type: DSG and CVT transsmision

Mode:
OBD mode: ECU remap
Boot mode: ECU Repair (W/R EEPROM)

via OBD:
DQ200 (0AM) Write/Calibrate
DQ250C (02E) Read/Write/Calibrate
DQ250E/F (02E) Write/Calibrate
DQ200MQB/G2 (0CW) Write/Calibrate
DQ250MQB (0D9) Write/Calibrate
VL300/V30 (01J/0AN)Write/Calibrate
VL381 (0AW) Write/Calibrate
DL501/G2 (0B5) Write/Calibrate
DQ500 (0BH/0BT) Read/Write/Calibrate

Boot mode:

DQ200/MQB/G2 Boot (MICRO) Read/Write/Calibrate
DQ200/MQB/G2 Boot (EEPROM) Read/Write
DQ250E/F/MQB Boot (MICRO) Read/Write/Calibrate
DQ250E/F/MQB Boot (EEPROM) Read/Write
VL300/V30 BSL (FLASH) Read/Write/Calibrate (open dsg computer)
VL300/V30 BSL (EEPROM)Read/Write/Calibrate (open dsg computer)
VL381 Boot (MICRO) Read/Write/Calibrate
VL381 Boot (EEPROM) Read/Write
DL501/G2 Boot (MICRO)Read/Write/Calibrate
DL501/G2 Boot (EEPROM) Read/Write

KTM Flash workable DSG list:

1) DQ200 – BOOT – ALL, OBD –ALL, except K-Line 0AM
2) DQ250 – BOOT – E/F/MQB , OBD – All
3) DQ500 – 0BT/0BH (NOT 0DL!) Only read/write via OBD
4) VL300/V30 – BSL – All, OBD –except KW1281
5) VL381 – ALL
6) DL501 -ALL

Operation tips:

OBD Mode:

If you have operational interruption issue during the OBD reading process, turn off ignition and read again.

If a missing/broken file burns the transmission computer, you are allowed to reset data via boot mode.

Boot mode:

Strongly recommend to use the switch board to enable power automactic off/on.

DQ500 Read/Write:

Directly connect KTMFlash with transmission computer. Manually turn on/off power by controlling 15 PIN J2534. The second gear should always be on.

Read/Write VL300/V30 via BSL:

Need to drill a hole on the transsmision computer to add a 1Ω resister to GND with a probe. Then connect to k-line. (Strongly recommed to use a switch board as well.)

Location to drill a hole shown as picture below.

Connection diagram:

Red- +12V

Black – GND

Yellow – CAN-HIGH

Blue- CAN-LOW

KTMFlash (pcmflash software) read DQ200/DQ250 in action:

Read DQ200

Read DQ250

Read Audi C7 DQ381

This post is from China OBD2, Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc.

This Post: KTMFLASH VAG DQ200 and DQ250 User Manual From ChinaOBD2 Official Blog
Please keep this link if you copy the post!