KTMFlASH ECU flasher supports VAG DQ200 DQ250 DQ500 VL381 DL501 Direct-shift gearbox Transmission read and write via OBD or boot mode.
Type: DSG and CVT transsmision
Mode:
OBD mode: ECU remap
Boot mode: ECU Repair (W/R EEPROM)
via OBD:
DQ200 (0AM) Write/Calibrate
DQ250C (02E) Read/Write/Calibrate
DQ250E/F (02E) Write/Calibrate
DQ200MQB/G2 (0CW) Write/Calibrate
DQ250MQB (0D9) Write/Calibrate
VL300/V30 (01J/0AN)Write/Calibrate
VL381 (0AW) Write/Calibrate
DL501/G2 (0B5) Write/Calibrate
DQ500 (0BH/0BT) Read/Write/Calibrate
Boot mode:
DQ200/MQB/G2 Boot (MICRO) Read/Write/Calibrate
DQ200/MQB/G2 Boot (EEPROM) Read/Write
DQ250E/F/MQB Boot (MICRO) Read/Write/Calibrate
DQ250E/F/MQB Boot (EEPROM) Read/Write
VL300/V30 BSL (FLASH) Read/Write/Calibrate (open dsg computer)
VL300/V30 BSL (EEPROM)Read/Write/Calibrate (open dsg computer)
VL381 Boot (MICRO) Read/Write/Calibrate
VL381 Boot (EEPROM) Read/Write
DL501/G2 Boot (MICRO)Read/Write/Calibrate
DL501/G2 Boot (EEPROM) Read/Write
KTM Flash workable DSG list:
1) DQ200 – BOOT – ALL, OBD –ALL, except K-Line 0AM
2) DQ250 – BOOT – E/F/MQB , OBD – All
3) DQ500 – 0BT/0BH (NOT 0DL!) Only read/write via OBD
4) VL300/V30 – BSL – All, OBD –except KW1281
5) VL381 – ALL
6) DL501 -ALL
Operation tips:
OBD Mode:
If you have operational interruption issue during the OBD reading process, turn off ignition and read again.
If a missing/broken file burns the transmission computer, you are allowed to reset data via boot mode.
Boot mode:
Strongly recommend to use the switch board to enable power automactic off/on.
DQ500 Read/Write:
Directly connect KTMFlash with transmission computer. Manually turn on/off power by controlling 15 PIN J2534. The second gear should always be on.
Read/Write VL300/V30 via BSL:
Need to drill a hole on the transsmision computer to add a 1Ω resister to GND with a probe. Then connect to k-line. (Strongly recommed to use a switch board as well.)
Location to drill a hole shown as picture below.
Connection diagram:
Red- +12V
Black – GND
Yellow – CAN-HIGH
Blue- CAN-LOW
KTMFlash (pcmflash software) read DQ200/DQ250 in action:
Read DQ200
Read DQ250
Read Audi C7 DQ381
This post is from China OBD2, Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc.
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: Car Key Programmer cat Code Reader ECU Chip Tunning EEPROM EPROM key Key Pro OBD2 program vag wholesale
Related Posts
How to Install the software of Iprog+ Programmer Iprog Pro Programmer?
2019.04.28
John Deere Service Advisor 5.3.225 (replaces 5.2) Offline 2023 Construction and ...
2024.01.28
How to do G30 VLD (low beam) coding with ENE cable
2019.12.19
(Solved) PCM Flash Crack Error: USB dongle is not available
2019.03.15
VIIPlusLoader 08.021.10(BETA) FULL Installer
2021.09.8
GLK 250 cdiX204 AKL Solution with CGMB
2023.04.13
Review on testing GM Tech2 and TIS 2000 Program
2019.05.12
VAS 5054A Firmware Update (esp. for bad BT module)
2019.09.24
Renault CAN Clip V195 and Consult 3 III For Nissan Professional Diagnostic Tool ...
2020.07.14
How to make Xentry Passthru 12.2018 work with Actia XS 2G
2019.03.13