This instruction show you guide on how to remove temperature sensors B6,B7,B9,B26,B33,B5,B10,B34,B48,B1,B13.
Related Contents:
2022 MTU DiaSys 2.74 2.72 Engine Diagnostic Software Free Download
MTU Engine Diagnostic USB-to-CAN Adapter with Cables
Removing temperature sensors (B6, B7, B9, B26, B33)
The sensors are identical with regard to design and electrical system. Removal of the sensors is identical.
The arrangement and position of the sensors is shown in the section “C507.98.01 Overview”.
For the sensors listed, the following must be noted before removal:
Sensor B6 (engine coolant temperature)
Before removal of sensor B6, the coolant must be drained and refilled after installation. The necessary procedure and the safety instructions to be followed are described in the operating instructions, section “Engine coolant changing”.
Sensors B7 (lube oil temperature sensor)
When sensor B7 is removed, small quantities of engine oil may emerge. Measures must be taken to collect this engine oil (e.g. suitable containers must be provided).
Sensor B26 (charge air coolant temperature)
Before removal of sensor B26 the coolant must be drained and refilled after installation. The necessary procedure and the safety instructions to be followed are described in the operating instructions, section “Charge air
coolant changing”.
Sensor B33 (fuel temperature)
When sensor B33 is removed, small quantities of fuel may emerge. Measures must be taken to collect this fuel (e.g. suitable containers must be provided).
Release bayonet lock (1) and withdraw connector (2).
Place wrench on nut (3) and unscrew sensor.
Removing pressure sensors (B5, B10)
The sensors are identical with regard to design and electrical system. Removal of the sensors is identical.
The arrangement and position of the sensors is shown in the section “C507.98.01 Overview”.
When sensor B5 is removed (lube oil pressure), small quantities of engine oil may emerge. Measures must be
taken to collect this engine oil (e.g. suitable containers must be provided).
Release bayonet lock (1) and withdraw connector (2).
Place wrench on nut (3) and unscrew sensor.
Removing pressure sensor (B34)
The arrangement and position of the sensor is shown in the section “C507.98.01 Overview”.
When sensor B34 is removed (fuel pressure after filter), small quantities of fuel may emerge. Measures must be
taken to collect this fuel (e.g. suitable containers must be provided).
Release bayonet lock (1) and withdraw connector (2).
Place wrench on nut (3) and unscrew sensor.
Removing pressure sensor (B48)
The arrangement and position of the sensor is shown in the section “C507.98.01 Overview”.
When sensor B48 is removed (H.P. fuel pressure), small quantities of fuel may emerge. Measures must be taken to
collect this fuel (e.g. suitable containers must be provided).
Release bayonet lock (1) and withdraw connector (2).
Place wrench on nut (3) and unscrew sensor.
Removing speed sensors (B1, B13)
The sensors are identical with regard to design and electrical system. Removal of the sensors is identical.
The arrangement and position of the sensors is shown in the section “C507.98.01 Overview”.
Release bayonet catch (1) of speed sensor (2) and remove
connector (3) from engine wiring system.
Release and remove screw (4).
Carefully withdraw speed sensor (2).
More topic about MTU,please refer to https://www.chinaobd2.com/
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat
Related Posts
Yanhua Mini ACDP program key on Land Rover KVM (MC9S12XEQ384 112Pin)
2019.04.9
Keydiy Mini KD Mobile Key Remote Maker Generator for Android & IOS System
2018.12.17
Xhorse Remote Tester V2 Operation Guide
2023.03.15
How to Remove and Calibrate Primary Hydraulic Power System for New Holland
2024.01.28
How to solve the problem EPC WIS Application Blocked by Java Security?
2019.02.25
QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit
2024.08.24
How to Program Volvo Truck Transponder Key with PTT 2.7?
2019.03.13
How to use gm tech2
2024.01.28
Autocom CDP Pro “Unable to read” and “Firmware version not load” Solution...
2019.02.24
BMW E46 Type Pressure Monitoring Coding by INPA NCS Expert
2019.03.4