This instruction show a guide on how to perform SKIM initialization for Chrysler vehicles.The model years and vehicles must be equipped (optional) with Sentry Key Theft Deterrent System (SKIM) (sales code GXX) for this bulletin to apply. And for more about Chrysler,check here:Chrysler Repair Projects
MODELS:
2001 – 2004 (AN) Dakota
2004 – 2005 (CS) Pacifica
2001 – 2003 (DN) Durango
2002 – 2005 (DR) Ram Truck
2004 – 2005 (HB) Durango
1999 – 2000 (JA) Breeze/Cirrus/Stratus
2001 – 2005 (JR) Sebring Convertible/Sebring Sedan/Stratus Sedan
1998 – 2000 (JX) Sebring Convertible
2002 – 2005 (KJ) Liberty
1999 – 2004 (LH) 300M/Concorde/Intrepid/LHS
2005 (LX) 300/Magnum
2005 (ND) Dakota
2000 – 2005 (PL) Neon/SX 2.0
2001 – 2005 (PT) Chrysler PT Cruiser/Chrysler PT Cruiser Convertible
2001 – 2005 (RS) Town & Country/Caravan/Voyager
2001 – 2005 (ST) Sebring Coupe/Stratus Coupe
1998 – 2005 (TJ) Wrangler
2004 – 2005 (VA) Sprinter
1999 – 2004 (WJ) Grand Cherokee
2005 (WK) Grand Cherokee
1999 – 2001 (XJ) Cherokee
2005 (ZB) Viper
2004 – 2004 (ZH) Crossfire Coupe/Crossfire Roadster
THIS PROCEDURE APPLIES TO ALL LISTED VEHICLES EXCEPT SEBRING COUPE/STRATUS COUPE (ST), CROSSFIRE, AND SPRINTER.
When a Powertrain Control Module (PCM) is replaced on vehicles equipped with the Sentry Key Theft Deterrent System (SKIM), it must be initialized to properly function with the anti-theft module. This is accomplished at a Chrysler Group Dealer by using the DRBIII or StarSCAN Scan Tool to enter a PIN number.
When the PIN number is not available from the vehicle owner this can be accomplished by writing the Vehicle Identification Number (VIN) into the PCM using the “VIN Write Function”.
NOTE: After performing this procedure on vehicles equipped with Chrysler Group’s Next Generation Controller (NGC), Diagnostic Trouble Code (DTC) “P0633 – SKIM SECRET KEY DATA NOT STORED IN PCM” will be set. This DTC will not affect vehicle or system performance and cannot be erased.
SEBRING COUPE/STRATUS COUPE(ST)
Initializing the PCM on these vehicles requires the use of a Daimler Chrysler scan tool (DRBIII), J1962 MMC Cable, and ST22 PCMCIA Diagnostic Card. This equipment is available for lease from DaimlerChrysler for short periods of time. To lease the DRBIII call 1-800-801-5420. A credit card deposit will be required.
The DRBIII will be shipped within 24 hours to your location by an overnight delivery service. When the DRBIII is returned, your credit card will be charged the lease price.
PCM INITIALIZATION PROCEDURE CROSSFIRE/SPRINTER:
1.Before replacing the PCM, with the ignition switch in the “RUN” position, determine the part number of the PCM software. Connect the CH9043 MUX Cable, and the DRBIII(with the CH9044 Crossfire Software card or CH 9087 Sprinter Software card plugged into it); to the vehicle. Using the DRBIII select:
a.“DRBIII Standalone”
b.“1998-2005 Diagnostics”
c.Make the appropriate selection: “2004-2005 Crossfire” or “2003-2004 Sprinter”
d.“System Select”
e.“Engine”
f.Record the ten(10) character “P/N” on the repair order for later reference.
2.Open TechAUTHORITY. TechAUTHORITY is available on the internet, www.techauthority.com
3.At the “Home” page, open the “Powertrain Control Module Initialization” link.
4.Open the “Coding String Calculator for Sprinter & Crossfire Vehicles” link.
5.Open the “Select Module” pull down menu and select “PCM”.
6.Select the appropriate “Transmission Type” button(Manual or Automatic).
7.Carefully enter the 17 character VIN.
8.Carefully enter the PCM software p/n recorded on the repair order in Step 1.
9.Select the “Calculate” button at the bottom of the window.
NOTE: TechAUTHORITY will automatically populate the “Coding String”, “SCN”, and “CheckSum” information.
10.Print the information from the technician’s PC.
11.Using the DRBIII select:
a.“1.DRBIII Standalone”
b.“1.1998-2005 Diagnostics”
c.Make the appropriate selection: “5.2004-2005 Crossfire” or “6.2003-2004 Sprinter”
d.“1.System Select”
e.“1.Engine”
f.“9.Miscellaneous Functions”
g“6.Read PCM Coding”
h.Verify that the PCM coding string on the DRBIII matches the coding string on the sheet printed from the technician’s PC.
NOTE: The SCN on the DRBIII may not match with the SCN Printed from the technician’s PC. This is OK.
12.Turn ignition switch to the “LOCK” position.
PCM INITIALIZATION PROCEDURE SEBRING COUPE/STRATUS COUPE(ST):
1.Perform the “Registration Procedure” described in service bulletin 08-036-04. This service bulletin, including the password, is available on the internet at: www.techauthority.com under the “Powertrain Control Module Initialization” link
This post is from China OBD2, Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc. The main popular diagnostic tools for workshop are:Vag COM, VAS5054A, GM Tech2, iProg+ Programmer, Orange 5 programmer, Scania VCI3, etc.
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: Car Key Programmer cat Code Reader ECU Chip Tunning gm iprog key Key Pro lish OBD2 original printer program Scania VCI vci wholesale
Related Posts
Autel Maxisys ELITE II vs. MS909 vs. MS919
2024.01.24
MSOP8(MSOP-8 To DIP8) Socket Adapter For Chip Programmer
2018.12.17
How to perform hydraulic pump pressure test for New Holland T6030 tractor
2024.01.28
Super MB Pro M6+ Review: Supports BMW E-SYS
2023.04.1
How to Use DMS-5 to Calibrate Swash Plate Angle
2023.05.5
Liebherr R9600 Hydraulic Excavator Oil Filter Replacement Guide
2023.04.3
Perkins EST Software Perform ECM Flash for 404F-22T Engine
2020.08.27
New Holland CX8080 Elevation Lower Cleaning Shoe Repair Kits: Solving Cracks and...
2024.01.28
Honda Accord 2018 Mileage Correction by iProg Pro
2023.04.4
How to Disable DPF for BOSCH EDC17C81 EDC17C53 EDC17C63
2023.04.2