Here is a easy step guide on How to reflash ABS module and program new ABS module for Ford by VCM II IDS.And this article show it simply in text format,and at end of article I will put a detail video guide,you would like to watch the video to get more detail info.Hop it is helpful.
What You Need For Ford ABS Module Programming?
1. A laptop
2. Ford IDS Software.(Ford IDS v106 Software Free Download)
3. Hardware as Ford VCM II or VXDIAG Ford
Procedures of reflash ABS Module:
1.Install Ford IDS software on your laptop.
Read 🙁Ford IDS Software Installation Guide (Original & Crack))
2. Connect the VCM hardware to vehicle and launch Ford IDS software.
3. Turn ignition key to “ON” position,select “Start New Session”–>”All other”
4. Wait progress bar complete,and then click tick
5. Select “None Of The Above”—>select ”Not equipped”,then it will show the vehicle specification,click “YES”
6. Switch the toolbar,and then select “Module Programming”–>select “ABS”.
And then software display below massage:
“During Module Programming this module goes through a VIN verification process.
This process compares the VIN in this medule with the VIN in other modules on the vehicle.You may see the VIN verification screen more than once depending upon your response to the question”
7. Tab “Enter”,the software dislay VIN:1FMCU03759KB00229. Click “YES” or tab “Enter” to continue.
Wait and the click “YES”
Make sure your key is on,and tab “Enter”
Then display the massage:
“The module you are about to program has multiple internal memory locations.During programming you may see multiple bar graphs indicating the programming sequence of each memory location.Please do not disconnect any cables or turn the igniton key off uless instructed to do so by the diagnostic tester.”
ABS Module is programming,pls wait….
Set ignition switch to OFF (Position 0)
Operation in progress,wait for complete
Set the ignition swithch to ON
Calibration has been loaded and checked,then tab”enter”
8. Switch the toolbar,and select–>”Self Test”–>”All CMDTCs”,it will read the DTCs
9. And then,screen show as below,select “U002B:08-08-RCM”—>select “clear DTCs”—>select “tick” to clear.Then wait for DTCs clear completing
When the DTCs clear completing,the ABS programming done!
If you want to program for a new ABS Module,follow below text describtion.And check detail in the video.
1. Select “Programmable Module Installation”—>select “ABS”
2. Set ignition switch to ON
3. Configuring please wait…
4. Set ignition switch to OFF(Position 0)
5 .Operation in progress…wait for a few seconds and we are going…
6. Set the ignition switch to ON
7. It will show you “Module configuration complete”
8. Clear the DTCs
Ford ABS Module reflash and programming video guide:
Now we can also use FVDI J2534 Diagnostic Tool for Ford & Mazda Support Online Module Programming to diagnostic Ford cars, from the instructions of FVDI J2534, it’s better than VCM II for Ford. more information about FVDI J2534 can click here…
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat Ford FVDI J2534 j2534 key laptop Mazda program vcm VCM II wholesale
Related Posts
Why Choose SDConnect C4 in C5 housing
2019.12.19
How to Sovle issues when programming BCM by tech2
2024.01.28
What kinds of key cutting machine do you use?
2019.12.19
Super Dprog5 IMMO Odometer Airbag Reset Tool 3 in 1 for BMW Benz and VAG vehicle...
2018.12.17
NYO 4.0 Calculator 2015 2017 Full Free Download
2019.03.18
Original KEYDIY KD900+ Mobile Remote Key Generator Best Tool for Remote Control
2018.12.17
Delphi DS150E Diagnose Audi A3 2009 Gateway Real-time Data
2019.05.31
How to use EUCLEIA TabScan S8 for car’s service reset function?
2019.03.27
How to install TIS2000 and GlobalTIS for GM Tech2 Scanner
2022.03.22
How to Use “X-431 FIX” Function by Launch X431 Pad V / VII (Support Free Trial)...
2023.04.2