Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Hitachi ZX890-7 Excavator Main Controller Removal Guide

Posted on April 17, 2023April 17, 2023 by VCDS
Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-5

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to remove main controller for HITACHI ZX890-7 excavator.

 

Related Contents:

Hitachi MPDr v2.56 v2.25 Diagnostic Software Free Download

Hitachi Excavator ZX-7 Service Repair Workshop Manual 2021

Hitachi Dr.ZX Excavator Diagnostic Tool Cable

 

Procedures:

1.Set the machine position for inspection and maintenance.

2 IMPORTANT
Set the key switch to the OFF position. Wait 5 minute or longer, and then set battery disconnect switch to the OFF position.
Set the battery disconnect switch to the OFF position.

3.Open door (1).

Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-1

4.Fold seat (2). Slide seat (2) to the front end.
5.Remove caps (3) (4 used).
6.Remove cover (4).

Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-2

7.Remove screw (5), screws, washer (6), bolts (15), and washers (16). Remove the cover (14) assembly.
13 mm
8.Remove screws, washers (8) (2 used) and bolts, washer (10).

9.Disconnect connector (17) and connectors (18) (2 used). Remove cover (9).

Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-3

10.Remove screws, washers (7) (2 used), bolts (12) (2 used), and washers (13) (2 used). Remove the cover (11) assembly. At this time, duct (20) is also removed at the same time.
13 mm

Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-4

11.Disconnect connectors (24) (6 used).

12.Remove bolts, washers (22) (4 used). Remove the MC (23) assembly.

Hitachi-ZX890-7-Excavator-Main-Controller-Removal-Guide-5

13.Remove screws, washers (25) (4 used). Remove MC (23) from brackets (21) (2 used)

More repair cases for Hitachi excavator,please refer to:Hitachi Excavator Trouble Repair.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Hitachi ZX890-7 Excavator Main Controller Removal Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: key

Post navigation

Prev: Prev: How to use OBDSTAR X300DP Plus
Next: Next: Doosan ISUZU 6UZ1 Engine Lost Communication with TCM U0101 Solution

Related Posts

BT TruckCom TE v2.8 Multilanguage Download

BT TruckCom TE v2.8 Multilanguage Download

2019.07.19

Cheap BMW OBD2 reader reviews: Autel AP200, INPA, ISTA / P, Foxwell NT530, C110

Cheap BMW OBD2 reader reviews: Autel AP200, INPA, ISTA / P, Foxwell NT530, C110

2019.12.24

Xhorse Condor XC-009 Key Cutting Machine for Single-Sided keys and Double-Sided Keys

Xhorse Condor XC-009 Key Cutting Machine for Single-Sided keys and Double-Sided ...

2018.12.17

UPA Programmer & NYO 4.0 Change Mileage for Renault ESPACE HC908AZ60

UPA Programmer & NYO 4.0 Change Mileage for Renault ESPACE HC908AZ60

2020.10.11

How to Use Autek iKey820 Program Keys for Dodge RAM 2009

How to Use Autek iKey820 Program Keys for Dodge RAM 2009

2023.06.10

Caterpillar ET 2018A Electronic Technician Software Free Download

Caterpillar ET 2018A Electronic Technician Software Free Download

2019.07.24

Keydiy Mini KD Mobile Key Remote Maker Generator for Android & IOS System

Keydiy Mini KD Mobile Key Remote Maker Generator for Android & IOS System

2018.12.17

Newest Super SBB2 Key Programmer Oil/service Reset/TPMS/EPS/BMS Handheld Scanner

Newest Super SBB2 Key Programmer Oil/service Reset/TPMS/EPS/BMS Handheld Scanner

2018.12.17

How Use BMW ISTA-P Generate BMW IBAC Enable Codes

How Use BMW ISTA-P Generate BMW IBAC Enable Codes

2019.07.24

What’s the difference of XPROG-M V5.84 X-PROG Box ECU Programmer and XPROG-M V5.74 ?

What’s the difference of XPROG-M V5.84 X-PROG Box ECU Programmer and XPROG...

2019.02.26

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Scania Truck CAN Communicatinon Fault Engine Control Unit Error Solution
  • Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution
  • OBDSTAR ECU Flasher Software Gets a Major Upgrade in June 2025
  • How to Remove HV Battery Cooling FAN for HINO Truck with J05E Engine
  • How to Calculate BMW F/G Series by APPRO2 for Free?

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2