This article show a guide on how to use DiagBox Lexia P2000 to program new keys for Peugeot 307 BSI.Hope it Helps!
Preparations:
DiagBox Software Free Download All Version Here https://mega.nz/#!h9kFlDrZ!DCpvnmCPB_NDm-wFrea0mGiKDE5giM96-lSXXC1uSIg
How to Install DiagBox v8.01 Software
Lexia3 PP2000 Interface
Preocedures:
Connect interface to vehicle and run DiagBox software
Select “PEUGEOT”
Vehicle model “307”
After vehicle idenfitication,it will show you the VIN,and ask “IS THE VIN READ ON THE VEHICLE CORRECT?”,click “YES” icon to continue
Then select “DAIGBOX”
Select “REPAIR”
Then DiagBox will each control units
After control units test completing,click “BSI”
Select “PACK REPARATION”
Select “LEARN”
Select “PROGRAMMING OF KEYS”
Key programming procedure:
To program the keys,you must have
1.The customer’s confidential card
2.All of the vehicle’s keys
WARNING:The keys which are not programmed in this programming procedures will no longer permit starting of the engine.If a new key is added,it is possible to reprogramme all of the keys.
Click “Yes” icon to continue
In order to program the keys,the code indicated on the customer’s confidential card must be entered.
WARNING:If a confidential code error occurs,programming will be prohibited.
You can confirm the confidential code by means of the procedure in force in your country.
INFORMATION:Whether you are in the process of downloading replacing,or initialising the BSI,the diagnostic tool will automatically use the code already entered at the time of the intialising of the confidential code.
Enter the EXAT code indicated on the customer’s confidential card
WARNING:There is no letter “o” or letter “i” in the confidential codes
Click “Yes” to continue
Confidential code correct
The built-in system interface is ready for programming of the keys
Click “Yes” to continue
Now enter the key number to learnt
The nunber of keys to programmed can not exceed 5
Click “Yes” to continue
Switch off the ignition
You have 15 seconds within which to switch on the ignition positive (+APC) using the key to be programmed.
Key programmed.Switch off the ignition and take out the key
For program next key,you need to insert the next key in the ignition
The switch off the ignition
You have 15 seconds within which to switch on the ignition positive (+APC) using the key to be programmed.
Key programmed.Switch off the ignition and take out the key
Number of keys to be programmed=2
Number of keys programmed=2
IMPERATIVE:Before making any attempt to start the engine-Check that the handbrake is on
For an automatic gearbox,check that the gear lever is in position “P”(Park)
For a manual gearbox,check that the gear lever is in neutral
Click “Yes” to continue
Pesynchronise the High Frequency Remote Controls
Procedures:
1.Switch off the igniton and take out the key
2.Wait one minute without pressing the buttons of any remote control
3.Insert a key in the steering lock,turn it to ignition positive (IGN+)
4.Within 1 seconds,press the locking button for 2 seconds syntax error @*10syntax error @*5
5.Switch off the ignition and take out the key
6.Repeat the procedure with the other keys from point N*3.otherwise move on to point N*7
7.Wait 30 seconds,the remote controls are active
This procedure can be used at any time and without using diagnostic equipment
WARNING:Pressing one of the buttons of a remote control while it is desynchronised resultes in the switching of the built-in systems interface to antiscanning mode for one minute
Resynchronisation is prohibited during this phase.
Done!
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat key Lexia-3 Peugeot program Remote
Related Posts
How to Cheaply Add Horsepower with an ECM Flash
2024.01.28
Detroit GHG14 Engine Idle Does not Go into Continuous Run Mode
2024.01.24
Short USB Cable for Lexia-3 PP2000 Diagnostic Tool for Peugeot and Citroen
2018.12.17
GLK 250 cdiX204 AKL Solution with CGMB
2023.04.13
GM tech2 clone exercise 2000 C5 Corvette ABS pump motor successfully
2019.05.12
Toyota Lexus Electronic Parts Catalog 2019 2018 2017 Free Download
2019.06.17
Volkswagen Golf 2019 Key Adding by Autel IM608 Pro2
2023.04.2
MB SD C4 with EVG7 manual incl. FAQ , setup etc
2019.03.11
SDconnect c4 DAS not work after network cable is connected (fixed)
2019.12.12
Original Autek IKey820 Key Programmer Universal Car OBD Key Programmer
2018.12.27