How to Setup Cummins Insite 8.2.0 work with Nexiq usb link

Posted on by VCDS

This article show a guide on how to use setup/configure Insite 8.2.0 work with Nexiq usb link. Cummins INSITE 8.2.0 truck software is also compatible with Inline 5, Inline 6, DPA5, Nexiq and Xtruck data link adapters. Cummins Insite Related Contents: How to Update Cummins Insite Software for Win 7/Win 8 Original Cummins Insite 8.2.1.155…

+

DIY:How to Remove ECU for Toyota FT86

Posted on by VCDS

This article show a guide on how to remove ECU for Toyota FT86.It is very easy for you to perform the ECU removal,and it take you about 15 minutes to complete it operations. For some ECU chip tuning or immo data reading,you need to read out ECU data file,so you need to open the ECU…

+

What is the Difference Between Ford IDS and FCOM

Posted on by VCDS

This post describes comparison of functions of FCOM with original Ford Motor Diagnostics IDS (Integrated Diagnostic System). Control unit selection Main difference between concepts of program FCOM and system IDS is in user approach to vehicle and its systems. The IDS uses so called Function system, which first chooses function (e.g. Read trouble codes) and…

+

OPCOM VAXU-COM Airbag Coding Guide for Opel

Posted on by VCDS

The new airbag control ECU is not configured. When a new airbag ECU is fitted to a car, it must be configured in order to work properly. OP-COM currently supports the coding of SAB6, and SAB8 airbag control units.This article from chinaobd2.com is about OPCOM VAXU-COM Airbag Coding Guide for Opel. What You Need? Newest…

+

How to Use GM GDS2 Perform Bi-directional Controls

Posted on by VCDS

This article show you a guide on how to use GM GDS2 perform bi-directional controls,active the headlights,power door locks and power window motor. Preparations: GM GDS2 2019 v20.3.05100 Software Free Download How to Install GM GDS2 Software on Win XP/7/8 GM GDS Interface (GM MDI,VXDIAG GM NANO) Procedures: Connect GM GDS2 interface to vehicle,then run…

+

FCOM BCM Trailer Hitch Type Configuration for Ford Focus 2011

Posted on by VCDS

Here chinaobd2.com share the process on how to use FCOM to program/configure trailer module in BCM after trailer module replacement for Ford Focus 2011. Preparations: FCOM Ford OBD2 Diagnostic Software Download How to Install FCOM Diagnostic Software on Window/Linux Compatible Ford Modules: Mondeo 2006-2014Galaxy 2006-, S-Max 2006-, Focus 2010-, Kuga 2010-, C-Max 2010-, Transit Connect…

+

Nissan Consult 3 Plus VDR Setting Guide

Posted on by VCDS

This post show a guide on how to set Nissan Consult 3 Plus VDR.Hope it helps,and if you want to know more about Nissan Consult 3 Plus,check:Nissan Consult 3 Plus Projects. Related Contents: Nissan Consult 3 Plus Software Download How to Install Nissan Consult 3 III Plus Diagnostic Software Nissan Consult 3 Plus Clone Interface…

+

TDDi Fuel Injection Pump (FIP) Adjustment by FCOM

Posted on by VCDS

Fuel pump adjustment Information about unadapted fuel pump is displayed as an fault code B2139 (or U2510,B10DA-61). The pump is adjusted by OBD2 diagnostic connector. Connect to the engine control unit (PCM) by FoCOM. Function Fuel pump Adjustment can be found at the menu ECU Programming/Coding. Selection of any other coding functions such as PATS…

+

How to Remove and Disassemble Instrument Cluster for BMW Z3

Posted on by VCDS

This article shared by t-tony from zroadster.org forum.It show a guide on how to remove and disassemble instrument cluster for BMW Z3.Thanks for t-tony nice write up.And if you want to get more about BMW projects,check here:BMW Repair Cases What Tools You Need? 1.T20 1/4? drive socket and ratchet. 2.Small flat bladed screwdriver. 3.A plastic…

+