How to Use Cummins Insite Change Road Speed Parameter for Saf-T-Liner C2
Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc. Currently, the top selling product including: VCDS VAG COM Cable, iProg+ Programmer, Scania VCI3
In this instruction i will show you guide on how to use Cummins Insite diagnostic to change road speed parameters for Saf-T-Liner C2 bus.
Preparations:
Newest Cummins Insite 8.6 8.4 Free Download
How to Setup Cummins Insite 8.2.0 work with Nexiq usb link
Cummins Insite Change Road Speed Parameter Procedures:
Step 1: Connect the laptop to the bus by using the 9-pin diagnostic receptacle inside every C2 located above the driver’s left foot position.
Step 2:Click on your desktops Cummins INSITE Icon.
Step 3: Turn key in bus to on position. Bus does NOT need to be running.
Step 4: Click on “Connect to ECM” menu on left and then click “Connect” in pop up window.
Step 5: Click on “Features and Parameters”.
Step 6: Scroll down menu to Road Speed Governor and click on icon beside to expand its options. The menu is in alphabetical order for ease of use.
Step 7: Double click on MPH number on MAX VEHICLE SPEED.
Step 8: Enter the new MPH speed required and then click on the number. Note: North Carolina has specific laws for buses in operation. Please adhere to these laws for any bus in-service.
Step 9: Double click on MPH number on MAX ACCELERATOR SPEED and change to same value as MAXIMUM VEHICLE SPEED.
NOTE: New speed is displayed and old speed is displayed to the right.
Step 10: On tool bar at top of screen, click on the small computer icon to send info to engine’s ECM.
Step 11: Pop up window will indicate you are to turn ignition key off for 30 seconds. Do this and then click OK.
Step 12: NEW pop up window will tell you when to turn ignition key back on. When instructed, turn key on and click OK.
Step 13: Pop up window will indicate when all parameters were successfully written. Click OK.
Step 14: Click Icon on left to disconnect from ECM. When this is complete it is safe to remove laptop connections with bus.
This article tech Supported by China OBD2,
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: Car Key Programmer cat Code Reader ECU Chip Tunning iprog key Key Pro laptop OBD2 ops program Scania VCI VAG COM Cable VCDS VCDS VAG COM VCDS VAG COM Cable vci wholesale
Related Posts
Autel AP200 code scanner is great for BMW F10 5 series
2019.12.13
How to Disable Bosch MED9.1 IMMO for Audi,Touareg and Golf 6
2019.07.14
Toyota Previa MPV Smart Card All Keys Lost Programming Guide
2019.02.24
How to Install & Setup Original wiTECH Diagnostic Extender
2019.07.24
How to use EUCLEIA TabScan S8 for car’s service reset function?
2019.03.27
VXDIAG VCX DoIP Jaguar Land Rover Diagnostic Tool with PATHFINDER V182 & JL...
2018.12.23
Volvo PTT Do Cruise Control Parameter Programming for Mack I II III
2019.03.2
Scania SDP3 2.44.1 Scania Diagnos & Programmer 3 V2.44.1 Free download
2020.06.6
10PCS/lot JLR Mangoose V143 For Jaguar And Land Rover
2018.12.17
BMW FEM BDC Test Platform for FEM/BDC Key, KM reset and ECU Gearbox Programming
2018.12.17