Several days ago I got an error with my OPCOM 2014V Opel diagnostic tool, when I asked help on the forum, I found a nice friend shared the latest op-com FW 1.64, I have not tried yet because my opcom error has not solved, I write down processes, hope these helps.
Free download Opcom diagnostic tool FW 1.64:
https://mega.nz/#!CB91DAAL!fCPUZCimVAWcZlhdVpc31wIR0sL837iC4rbGl7WlKyU
Notice:All manipulations with the device you are doing at your own risk! (It haven’t been tested yet,just share by forum membmers)
∇∇∇∇∇
Here is another version Opcom Opel Firmware V1.99 PIC18F458 with software (Tested work 100%)
OPCOM Function:
1. It covers almost all Opel cars, even new cars with CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B.
2. The program lets you to read out and clear fault codes, shows you live data, lets you to perform output test.
3. The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples.
4. Since Opel uses many pin in the OBD connector, the diagnostic interface works as a multiplexer, and selects the appropriate pin for communication.
PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000)
5. Fault codes will be shown with all available information:
How to install OP-COM OPCOM FTDI CDM Drivers
Attention!
See the presence of the chip. There must be a [PIC18F458]. If there has a [OP-COM] chip then do nothing. You will get a 100% dead of OP-COM
An example, Instead PIC18F458 chip is OP-COM chip, so it can’t be reflashed.
Seen that the chip is PIC18F458, then go to the next step.
How to Setup OP-COM software
Connect OP-COM to the laptop
Then unzip [VAUX-COM_120309a + 131223d_GB + OcFlash China] file to desktop and Run the program [VAUXCOM.exe] to verify the correct installation of the drivers
->Click Settings
->Click Test interface
It means that the driver installed properly if the interface appear here. (pictures shown below)
Download the firmware and run the program [OCFlash.exe]
Specify the path to the [FW 1.64.hex]
Run the Test interface again and check that the OP-Com updated to version 1.64
You can now use the program [VAUXCOM.exe]
Vehicle model until 2015
OPCOM VAUX-COM 120309a Windows 7 32bit:
Recently, some OPCOM users respond that “I couldn’t get the cracked software to run on my windows 7 laptop but it was fine on my old XP one….”
Free download VAUX-COM 120309a:
https://mega.nz/#!sPBnlZqT!vzaV6dx66ol0Y3gDrWDSAYZFjtkoBJz0cEtmuXWeOFc
Operation system supported:
Windows XP;
Win 7 32bit
How to install OPCOM in WIN7:
The way of installing op-com in Win 7 is the same as that in Windows XP:
Tips on using VAUX-COM 120309a software:
1. Make sure there is dotnetfx35_SP1 patch on your windows XP or Windows 7 laptop, otherwise you are unable to run opcom software.
2.If you install the software on windows 7 laptop, you can only open it as Administrator, kindly check and follow the installation video inside CD
3. Never update it online, It will damage the OP-COM
Installation procedure:
Open “My Computer/ OP-COM (E:)” to copy all the files to a new established folder named “op-com” in “Local Disk (C:)”.
The send “OP-COM” from”Local Disk (C:)/op-com” to Desktop.
Install software for USB Serial Converter
Click “Next” with the selection of “Install from a list of specific location (Advance)”.
Select “search removable media” and “include this location in the research”, then to “Browse” for “Desktop/My Computer/Local Disk (C:)/op-com/Drivers”. Then click “Next”.
Click “Next”.
Click “Finish” for successful installation of the software for USB Serial Converter.
Computer management setup
Right click “My Computer” for “Manage”.
Select “Device Manager/PC-201103301537/Universal Serial Bus controllers/USB Srial Converter”.
Close the interface.
Run VAUX-COM 120309a and diagnosis
Open “Shortcut to CP-COM”.
Select “Settings”.
Click “Test Interface”. And click “Close” on “Interface Test Result”.
Click “Save Config” button, click “OK” for “Configuration saved”.
Select “Diagnostics”.
Click “Automatic Vehicle Information”.
Click “KWP-2000”.
…(diagnosis as you want)
(NOTE: this installation instruction can be available for OPCOM 1.45 or 1.59)
OP-COM user manual:
http://obd2-diag.blogspot.com/2015/09/op-com-user-guide.html
Operation guide included:
Opcom Immobiliser Guide
Opcom Airbag Coding
Opcom SDM Programming
Opcom Diesel Pump Programming
Opcom Manual DPF Regeneration
Opcom Injector Programming
Opcom New CIM Programming
Opcom Throttle Body Reset
Opcom Clear SDM Deployment Data
Opcom Towbar And Trailer Module Coding
Opcom Read Security Code
Opcom Service Interval Reset
DLC Locations
Opcom Cruise Control
Dis (Display) Code Index List
Replace the BCM
Easytronic
Save
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat DPF KWP2000 laptop lish OP-COM OPCOM program
Related Posts
How to update CNH EST diagnostic software
2024.01.28
Review on testing GM Tech2 and TIS 2000 Program
2019.05.12
VIIPlusLoader V08.022.01(BETA)-FULL-Installer for VCDS V22.30
2022.03.5
How to Do DPF Regen on 2012 VW Passat TDI with Launch X431 Pro5
2024.01.28
Volvo Premium Tech Tool PTT Accessory Kit Programming Guide
2019.05.14
How to Repair Lexus LX570 AB60F Transmission Clutch/Brake Damage
2020.09.16
Renault CAN Clip V195 and Consult 3 III For Nissan Professional Diagnostic Tool ...
2020.11.3
BMW FEM/BDC BMW F20 F30 F35 X5 X6 I3 Test Platform with a Gearbox Plug
2018.12.17
How to Setting SD C4 PLUS DOIP IP Address ?
2024.01.28
Good News:the software of MB SD C4 Star Diagnosis has been updated to V2019.3
2019.02.28