This installation guide for F series NBT iDrive share by my reader from BMW F30 forum.I rewrite it here,hope it helps!And if you want to do this job,try it at your own risk!!! And here it E series article:BMW E90 NBT EVO Retrofit Guide What you Need? Trim Removal Tool Plyers Torx Screw Drivers Phillips & Flat head screw drivers ENET cable with E-sys & PSdZData 1.Remove the center trim piece. 2.Unscrew the 6.5′ LCD Display with a phillips screw driver and fixate the 8.8′ LCD display. Remove the aircon control panel with a torx screw driver. 3.Unscrew the surrounding torx screws around the CIC head unit and extract from the console. 4.Disconnect all the wiring and connection from CIC Head Unit. 5.Once the head unit is removed, feed the magenta LCD cable through the air vents to the bottom of the console. 6.Remove iDrive Trim and connect the touch input module. 7.Disconnect CIC iDrive Controller cable. 8.Unlock CIC iDrive cable housing. 9.Eject two pins from housing. 10.Wrap the pins with electrical tape. 11.Feed cable through inner console. 12.Feed cable through this point in the console. 13.Wrap the NBT iDrive Pins in Electrical cable and feed it to the trim sidewall of the drivers seat. 14.Once the cable is fed through, tuck the remaining cables into the side wall. 15.Connect the cable to iDrive Controller housing and wrap the other in electrical tape. 16.Replace CIC Controller with a NBT touch controller by unscrewing the rear torx screws. Connect turquoise cable to newly modified iDrive cable. 17.Open the center console, remove the USB Trim by wedging a trim removal tool between the gaps. 18.Pull firmly to remove the trim and disconnect the cable. 19.Follow the same process and feed the khaki cable through the driver side trim and into the center console. 20.Connect the khaki cable to USB Connection trim and the other end of the modified iDrive cable. 21.Cable tie the old cable & slot back into place. 22.Feed the bluetooth handsfree cable towards the other end of the dash. 23.Remove the plastic cap on the side of the dash and feed bluetooth cable through. 24.Remove door seals. 25.Feed bluetooth microphone cable between side trim. 26.Now feed cable upwards to the headliner between the airbag. 27.Remove Bluetooth microphone cover from headliner. 28.Disconnect microphone from existing cable and plugin new microphone cable. 29.Connect all the cables according to their colour on their NBT head unit. 30 .**WARNING** This may or may not be applicable to you. Proceed at your own risk ! Since I didn’t have Harman Kardon Audio. I had to splice the cable to enable audio with a pair of plyers. 31.We will perform a wire jump. Cut a bit of the cable from Pin 13 and Pin 15. Wrap the unsheathed copper wires around each other forming a bond., make sure it’s firmly wrapped to avoid short circuiting. Mine isn’t done very well, So I recommend if you know a auto electrician have them assist you. 32.Now wrap the cable in heat shrink or electrical tape, which ever you prefer. 33.Connect the extended harness to the original one in the car, Female to Male. 34.Once all the cables have been inserted, insert the NBT Head Unit back into position. 35.In the boot of the car lift the cargo liner out of the way and it should reveal the CANBUS. Disconnect all the cables from CANBUS. 36.Once all the cables have been disconnected, Connect orange loop cable to existing cable 37.Turn on the ignition to test the NBT iDrive before attaching all the screws and trim. 38.Now connect your OBDII Cable to the OBDII port on the vehicle. Code the new NBT values with E-sys & PSdZData. Consult a coder or a friend for assistance to update the new values. 39.Installation is complete. Now sit back and admire your hard work. source http://f30.bimmerpost.com/ This post is from China OBD2, Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc. The main popular diagnostic tools for workshop are:Vag COM, VAS5054A, GM Tech2, iProg+ Programmer, Orange 5 programmer, Scania VCI3, etc.
This Post: BMW F Series NBT iDrive Installation Guide From ChinaOBD2 Official Blog
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
FCOM Ford OBD2 Diagnostic Software Introduction
Good News:the software of MB SD C4 Star Diagnosis has been updated to V2019.3
How to install VIDA2014D on Windows 8.1 / 10 Pro / Core x86 / x64 PC?
Automotive CAN Bus System Explained Instruction & Diagnosis
Diamond Logic® Builder Cluster Odometer Programming
All Benz diagnostic and programming: Benz Ecom VS SD C4
JINGJI Mini Vertical Key Cutting Machine Refined Version
FCOM Key On Engine Off KOEO Test for Ford Ka 1999
Newest Super SBB2 Key Programmer Oil/service Reset/TPMS/EPS/BMS Handheld Scanner
JDiag JD101 Code Readers Engine Scan Tool Check Engine Light Car Diagnostic Tool...