Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

ZF-ASTRONIC Transmission Without ZF-Intarder Oil Change Guide

Posted on June 13, 2023June 13, 2023 by VCDS
ZF-ASTRONIC Transmission Without ZF-Intarder Oil Change Guide (2)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

After long journey you need to change oil for ZF-ASTRONIC transmission.In this post,car-auto-repair.com show you guide on how to change oil for ZF-ASTRONIC transmission without ZF intarder.

ZF-ASTRONIC Transmission Without ZF-Intarder Oil Change Guide (1)

 

Related Contents:

ZF Testman Pro 10.5 Transmission Diagnostic Software Free Download

 

Oil may only be changed when the vehicle is horizontal and the engine is switched off.
Always change the oil after a long journey while the transmission oil is still at operating temperature and thin.

 

Draining Oil

1 Remove screw plugs (1, 2 and 3) from transmission and collect transmission oil in a suitable
container and dispose of in accordance with environmental regulations.
2 Clean screw plug solenoid and replace sealing rings.
3 Tighten screw plugs (1 and 2).

Tightening torque: 60 Nm

Filling Oil
1 Fill in oil through oil filling point (3).
2 The oil level is correct when the oil has reached the bottom edge of the oil filler hole and/or
when oil is already escaping out of the oil filler hole.
3 Tighten screw plug (3).
Tightening torque: 60 Nm.

 

Oil-Level Check
DANGER !
Too little oil in the transmission will result in transmission damage. RISK OF ACCIDENT!
Check the transmission oil level as part of vehicle servicing:

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: ZF-ASTRONIC Transmission Without ZF-Intarder Oil Change Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat key

Post navigation

Prev: Prev: How to Remove and Install Liner for New Holland CX8080 Combine
Next: Next: Detroit GHG14 Engine DOC Inlet Temperature Unable to Reach HC Dosing Solution

Related Posts

OBDSTAR X300 Classic G3 Read PSA BSI-Q05 EEPROM and PIN CODE Success!

OBDSTAR X300 Classic G3 Read PSA BSI-Q05 EEPROM and PIN CODE Success!

2025.02.28

Caterpillar ET 2018A Electronic Technician Software Free Download

Caterpillar ET 2018A Electronic Technician Software Free Download

2019.07.24

How To Do GM Control Module Programming With Multiple Diagnostic Interface (MDI/MDI 2)

How To Do GM Control Module Programming With Multiple Diagnostic Interface (MDI/...

2019.12.16

VCDS Perform Audi A4 ABS Coding Guide

VCDS Perform Audi A4 ABS Coding Guide

2019.02.24

VIIPlusLoader 08.021.10(BETA) FULL Installer

VIIPlusLoader 08.021.10(BETA) FULL Installer

2021.09.8

Perkins EST Software Perform ECM Flash for 404F-22T Engine

Perkins EST Software Perform ECM Flash for 404F-22T Engine

2020.08.27

How to Remove and Calibrate Primary Hydraulic Power System for New Holland

How to Remove and Calibrate Primary Hydraulic Power System for New Holland

2024.01.28

How to Perform Ford Inspection /Maintenance Setting

How to Perform Ford Inspection /Maintenance Setting

2019.07.22

How to Install the software of Iprog+ Programmer Iprog Pro Programmer?

How to Install the software of Iprog+ Programmer Iprog Pro Programmer?

2019.04.28

How to Get Approval Password for CNH EST Programming

How to Get Approval Password for CNH EST Programming

2023.09.1

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • ECUDESK Software Latest ECU Support List (2025.05)
  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2