Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation
VNCI PT3G Diagnostic Scanner is compatible with the original PIWIS driver and PIWIS software without the cracked patch. It can replace the original Porsche Diagnostic Tool PT3G, and supports Porsche 9PA 9YA 9YB 92A 95B 918 970 971 981 982 986 987 991 992 996 997 Y1A and all models from 1996 to the present. Check more details below.
Why choose VNCI Porsche PT3G?
Compared with OEM PT3G, Custom VAS 615A, and other PT3G tools, VNCI PT3G is the similar with OEM PT3G. Both support original PIWIS driver, CAN FD/DOIP, multi-version PIWIS, KW71 protocol (1995MY previous vehicles), Porsche vehicle 1996-2023, firmware update for free, plug and play.
Custom VAS 615A:
Change the PIWIS software driver based on the original VAS6154A hardware.
Defect: protocol layer communication logic is not complete, cannot do the whole car module diagnosis, programming, immobilizer and other functions.
Other tools do not support original PIWIS driver, KW71 protocol (1995MY previous vehicles), plug and play, needs PIWIS software patch and cannot support the old Porsche vehicles.
How to install VNCI Porsche PT3G PIWIS III device manager and driver PUD API?
Step 1: Install VNCI PT3G Device Manager
The device manager is used to update VNCI PT3G firmware online.
1.Free download VNCI PT3G firmware update tool (Device Manager)
https://mega.nz/file/auhgASRI#GKJl2Gnug5XB1mD_z4xyQ_nKuiPcQaFiDqIIUyXZj7A
2.Install VNCI_PT3G_Device_Manager setup.exe until finished.
3.Run VNCI PT3G Device Manager
Check device information serial number and firmware version
Check if the firmware and software version are the newest, if not, run an upgrade.
Step 2: Install and configure Actia PUD API driver
If use the VNCI PT3G HDD from UOBDII.com, the software and VCI are configured, don’t need to configure VCI driver any more. Plug and play.
If use the original or 3rd party PIWIS III software, need to configure VCI in driver PUD API, otherwise may fail to connect.
Make sure the device VCI shows as PT3G_VCI rather than 6154a or other J2534 VCIs.
Download PIWIS OEM driver (includes Actia PUD API Driver and patch) and extract zip file
PIWIS OEM Driver:
https://drive.google.com/file/d/1Q5FsebVBwXjAX6kcKjefAfLRrUbaDt2D/view
Actia-64.7z:
https://drive.google.com/file/d/16itKck3MgVzmOc0v9Gdm2oUramQpuDju/view
Copy and paste XS_D_PDU_API_64 folder to PiwisApps/VCI/Actia-64 folder (replace the existing folder)
Then open driver folder, run 3.4.1 patch. (Build connection between software and VCI)
Run ACTIA_D_PDU_API_Tester.exe program on PiwisApps/VCI/Actia_64/XS_D_PDU_API_64 folder
Select device module type as PT3G-VCI
Check if the serial number displayed in D-PDU API driver is the same as displayed in PT3G device manager.
If yes, click “Start” to run the software.
2024 VNCI PT3G Diagnostic Scanner for PIWIS:
https://www.chinaobd2.com/vp-vnci-pt3g-diagnostic-tool.html
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!