Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Super ICOM Pro N3+ Operation Guide

Posted on December 24, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Super ICOM Pro N3+ Operation Guide: 

1. Plug the N3+ into the power supply or connect the OBD to the test vehicle, and plug in the N3+’s USB cable.

Super ICOM Pro N3+ Operation Guide

2. Turn on the computer and plug in the computer USB cable.
3. Open the computer network configuration interface, find the Realtek USB FE Family Controller network

Super ICOM Pro N3+ Operation Guide

4. Click Properties–TCP/IPV4, and set the IP address as shown in the figure below.

Super ICOM Pro N3+ Operation Guide

5. Click OK to complete the wired network configuration.

6. On the same computer, if you replace a new N3+, you need to reset the IP. After the setting is completed, the computer is bound to the N3+. After disconnecting the USB cable, the network icon will disappear, and you don’t need to set the IP address again when you use the N3+ after the computer is wired or wirelessly connected to the Internet. .

7. Use the BMW special inspection software to test normally.

8. When using wireless detection, you need to unplug the USB cable on the computer first, and then you will find that the SSID is N3+ICOM-****, connect directly, enter the password 123456789, and you can use the BMW special inspection software directly without equipment.

9. When using the J2534 function of N3+ to test Mercedes-Benz, Toyota, Volkswagen, Honda, Land Rover, etc., first open the special inspection software, install the J2534 driver, select the PassThru menu in the special inspection software, select the ISO J2534 device in the list, and plug it in. For the USB connection cable between the computer and N3+, press and hold the N3+ switch button for 3 seconds, and the wired and wireless indicator light of the N3+ host will flash to test normally.

10. Use the DOIP function of N3+ to test the DOIP protocol of the new Mercedes-Benz, Volkswagen, Land Rover, etc.: first plug in the USB cable between the computer and N3+, press and hold the N3+ switch button for 3 seconds, the wired and wireless indicator light of the N3+ host flashes, and then turn on the computer For wireless, find N3+ ICOM-**** wireless, connect directly, enter the password 123456789, start the special inspection software, find the DOIP menu and test directly.

11. N3+ is a special inspection tool for BMW. It runs 100% of the special inspection program for BMW. The multi-function of N3+ is an auxiliary function. Within the test range of J2534 and DOIP, the result is consistent with that of the special inspection, but it cannot include all the functions and models of the special inspection. It is mainly for the CAN, K, DOIP function detection of new OBD models. It can replace J2534 detection line and ENET line.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Super ICOM Pro N3+ Operation Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: FoxFlash BMW EDC16C1 ECU Connection FAQ
Next: Next: 2023 Super ICOM PRO N3+ vs BMW ICOM Next

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua ACDP2 Program BMW G Chassis BDC2 All Keys Lost on Bench
  • Scania Truck ALM 000800 Interrupted LIN Communicatin Siren
  • BMW G Series BDC2 Module Virgin and Replacement by APPRO2
  • CG FC200 V1.2.9.2 Update: BMW Coolant Temperature Setting Added
  • Scania Truck ALM 000463 Motion and Inclination Detector,Calibration Fault

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2