This instruction provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer’s concern of poor shift quality.
Compatible Car Models:
2014 – 2015 (DS) Ram 1500 Pickup
2014 -2015 (LD) Charger
2014 -2015 (LX) 300C
2014 – 2015 (WD) Durango
2014 – 2015 (WK) Grand Cherokee
2015 (LA) Challenger
NOTE: This bulletin applies to vehicles equipped with the 845RE (Sales Codes DFL).
DISCUSSION:
The 845RE Automatic Transmission uses a sophisticated shift algorithm that includes learned information so that the shift quality remains excellent even as the transmission wears. This learned information is recorded in memory cells referred to “Adaptation Memory Cells”. Each applied clutch records the amount of time it takes to fill the clutch (Fast Filling Counter/Filling Time) and the amount of pressure (Filling Counter/Filling Pressure). The adaptation memory cells are set to zero (0) on every new transmission (new in vehicle and/or replaced for service) and when the transmission control module is replaced for service. In addition, the adaptation memory cells are set to zero (0) when the transmission control module adaptation memory cells are cleared using the wiTECH diagnostic scan tool. Until the adaptation has been learned/relearned, the transmission shift quality may not meet the customers expectations.
NOTE:Anytime the transmission has been overhauled (unless the Valve Body/TCU assembly (mechatronic) was replaced), the adaptation memory cells must be cleared using the wiTECH diagnostic scan tool.
The adaptation memory cells appear on the wiTECH for every clutch. Each clutch will include:
- Fast Filling Counter = the number of filling time events that has taken place
- Filling Time = +/- number of ms (milliseconds) from zero (standard set value).
- Filling Counter = the number of filling pressure events that has taken place
- Filling Pressure = +/- mb (millibar)/PSI (Pounds Per Square Inch) from zero (standard set value)
If the adaptation memory cell “counter” is zero (0), than the adaptation memory cell has not been updated. The filling counter ideally should be at least 12 and Fast Filling counter at least 4 to improve shift quality and with each subsequent count, shift quality will improve even more.
SYMPTOM/CONDITION:
Customers may indicate that their transmission shift quality does not meet their expectations.
DIAGNOSIS:
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available, verify all vehicle systems are functioning correctly. If any DTCs are present, record them on the repair order and repair as necessary before proceeding further with this bulletin.If the above symptom/condition is present, perform the Repair Procedure
SPECIAL TOOLS/EQUIPMENT REQUIRED:
REPAIR PROCEDURE:
NOTE: Transmission Quick Learn must be performed anytime the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced. It must also be performed when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Transmission Quick Learn is also one of the first steps to remedy a transmission shift quality concern on these vehicles.
1.Are there any active DTCs in the TCM’s memory?
a.YES>>> Using current published service information, diagnose and repair theconditions that set the DTC(s) before proceeding with this bulletin.
b.NO>>> Proceed to Step #2.
NOTE: 2015 model year vehicles equipped with the 845RE already contain software in the TCM to enable the Quick Learn procedure. However, 2014 model year vehicles require the Transmission Control Module to be updated to the latest software level.
2.Is your vehicle a 2014 model year?
a.Yes>>> Proceed to Step #3.
b.No>>> Proceed to Step #5.
3.Check the TCM calibration and see if it is up to date. Does the TCM software need to be updated?
a.Yes>>> Proceed to Step #4.
b.No>>> Proceed to Step #5.
4.Flash the TCM to the latest software level available referring to current applicable TCM flash Service Bulletins available in Service Information. If no other bulletins apply, use the provided LOP in this bulletin to perform the update. Proceed to Step #5.
5.Start the engine and monitor the transmission temperature on the EVIC.
6.With the vehicle located in a suitable area, allow the transmission to warm up to minimum of 55°C (131°F) by performing the following steps:
1)Apply the service brake.
2)Shift Transmission from Park to Reverse.
3)Shift Transmission from Reverse to Drive
4)Accelerate the vehicle to minimum of 45 mph to allow the transmission to cyclethrough each gear.
5)Drive the vehicle until the transmission temperature reaches 50°C (122°F).
7.Connect wiTECH diagnostic scan too to the vehicle.
8.Check for TCM DTC (Diagnostic Trouble Codes). Do not perform the Quick Learn procedure if TCM DTCs are present. Repair transmission as required.
9.Select the TCM module in wiTECH.
10.Select the “Misc Functions” tab.
11.Select “Reset Adaptive Values” and follow the on-screen instructions to reset the clutch adaptive values.
12.Next select the “Quick Learn” procedure, and follow the on-screen instructions to learn new clutch adaptive values. The Quick Learn procedure will take 2-5 minutes to complete.
13.Shift the transmission into Park and shut off the engine. The procedure is now complete. If there is still a customer concern of poor shift quality after performing this procedure, please perform the Transmission Adaptation Drive Learn Procedure outlined in service bulletin 21-012-14 or later version.
This post is from China OBD2, Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc. The main popular diagnostic tools for workshop are:Vag COM, VAS5054A, GM Tech2, iProg+ Programmer, Orange 5 programmer, Scania VCI3, etc.
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: Car Key Programmer cat Charger Code Reader ECU Chip Tunning gm iprog key Key Pro lish OBD2 original program Scania VCI vci wholesale
Related Posts
Diamond Logic® Builder Changing Programmable Parameters
2019.06.10
Detroit DDEC6 Engine Password Protection Removal by Backdoor Calculator
2023.04.3
How to Repair BMW E46 AUC Sensor ZKE unit with Xprog M V5.84
2019.03.1
How to Program 8C Key for Mazda 323 Manually
2019.02.24
Operation Steps for Vetronix Tech 2 GM Scanner
2024.01.28
How to Solve John Deere Service Advisor EDL V2&V3 Search Engine Error ?
2024.01.24
Class Parts Doc Agricultural 2011 Free Download
2020.09.16
JCB Stage V Engine K4732 Intake Air Temperature Sensor Out of Range
2023.04.6
Toyota Camry Steering Locked ECU trouble result in can’t start
2019.02.24
How to make Xentry Passthru 12.2018 work with Actia XS 2G
2019.03.13