Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

Posted on August 24, 2024August 26, 2024 by VCDS
QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Here is the instruction show you guide on how to solve QSK60 G CM2358 fault code 1367 Pre-Oil Filter Pressure Sensor Circuit- Voltage Above Normal or Shorted to High Source.

 

Related Contents:

INSITE 8.9.2 Engine Diagnostic Software

Cummings INLINE 6 Diagnostic Adapter

 

QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

Circuit Description

The engine control module (ECM) provides a 5 volt supply to the oil filter intake pressure sensor on the sensor supply circuit. The ECM also provides a ground on the sensor return circuit. The oil filter intake pressure sensor provides a signal to the ECM on the oil filter intake pressure sensor signal circuit. This sensor signal voltage changes, based on the pressure before the oil filters. The ECM will detect a low signal voltage at operating conditions when the oil pressure may be slightly lower. The ECM will detect a high signal voltage during high engine speeds or operating conditions when the oil temperature is low.

 

Component Location

The oil filter intake pressure sensor is located on the oil filter housing.

 

Conditions for Running the Diagnostics

This diagnostic runs continuously when the keyswitch is in the ON position.

 

Conditions for Setting the Fault Codes

The Engine Control Module (ECM) detected the engine oil filter intake pressure signal voltage was out of range high.

 

Action Taken When the Fault Code is Active

The ECM illuminates the white MAINTENANCE lamp or flashes the amber CHECK ENGINE lamp, indicating a maintenance condition, immediately after the diagnostic runs and fails.

A default value for the engine oil filter intake pressure reading is used.

 

Conditions for Clearing the Fault Code

To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.

 

The fault code status displayed by the recommended Cummings electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.

 

The ECM will turn off the flashing amber CHECK ENGINE lamp / MAINTENANCE lamp immediately after the diagnostic runs and passes.

 

The

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat key

Post navigation

Prev: Prev: JCB 3CX/4CX/5CX Loader Hand Throttle Position Sensor Service Steps
Next: Next: How to Remove and Install PCU for HINO J05 Engine

Related Posts

BMW 3 E46 Service Light Reset by Launch X431

BMW 3 E46 Service Light Reset by Launch X431

2019.03.21

How to make Xentry Passthru 12.2018 work with Actia XS 2G

How to make Xentry Passthru 12.2018 work with Actia XS 2G

2019.03.11

V3.9 CG100 Airbag Restore Devices Support Renesas

V3.9 CG100 Airbag Restore Devices Support Renesas

2018.12.17

VAS 5054A Firmware Update (esp. for bad BT module)

VAS 5054A Firmware Update (esp. for bad BT module)

2019.09.24

Update!How to Use Yanhua ACDP Renew BMW CAS1

Update!How to Use Yanhua ACDP Renew BMW CAS1

2019.03.8

How to Use HINO DX3 Simulation Function

How to Use HINO DX3 Simulation Function

2023.04.20

MAN MANTIS EPC Electronic Parts Catalogue Free Download

MAN MANTIS EPC Electronic Parts Catalogue Free Download

2019.07.31

G-scan2 Teach in Component Function Test on BMW X5 2009 Transmission

G-scan2 Teach in Component Function Test on BMW X5 2009 Transmission

2019.06.10

How to Enhance Jeep Renegade/Fiat 500X RA4 RG4 Radio Performance

How to Enhance Jeep Renegade/Fiat 500X RA4 RG4 Radio Performance

2019.07.19

Caterpillar C9 Hassle Code 00 231-12 ECM J1939 Machine Not Responding

Caterpillar C9 Hassle Code 00 231-12 ECM J1939 Machine Not Responding

2024.12.9

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2