Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Porsche PIWIS Programming Issue

Posted on December 9, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Porsche PIWIS Programming Issue

Situation Overview

Issue: After installing a PDK Shift Fork Position Sensor and performing basic settings with PIWIS 3, the check engine light came on, and PIWIS indicated a calibration failure. Fault code 10040 was displayed, indicating that the PDK transmission module was not programmed. The vehicle won’t start due to no communication with the DME.
Challenge: The local dealer refuses to program the car because it was imported directly.

Steps Taken

Basic Setting Execution: After installing the sensor, the initial fault codes were automatically deleted, and a basic setting was performed with PIWIS 3.
Calibration Failure: Upon executing the basic setting, the check engine light came on, and the calibration failed.
Fault Code Identification: Fault code 10040 was found, indicating that the PDK transmission module was not programmed.
Communication Issue: The car does not start due to no communication with the DME.
Dealer Refusal: The local dealer won’t program the car since it was not purchased from them.

Suggested Solutions

Remote Programming:

Consider contacting Y-Tech for remote programming assistance. They have experience with this type of issue and can provide support via TeamViewer.
Website: mbzexperts.com/contact

VAL Creation:

Ensure a “VAL” (Vehicle Analysis Log) is created during calibration. PIWIS goes through each ECU and records all details, including software levels.
Visit “Planet-9 Porsche forum” for more detailed instructions on this process.

Programming Tab Attempt:

If you haven’t already, try using the programming/coding tab in PIWIS to program the transmission controller.

Final Resolution

New Control Unit and Original PIWIS 3:

Contact Y-Tech confirmed that the control unit got disprogrammed. A new control unit has been ordered, along with the original PIWIS 3 (instead of a Chinese version), which might have caused the problem.
Plan to program the new unit with Y-Tech’s help.

Conclusion

The issue is expected to be resolved after receiving and programming the new control unit with the original PIWIS 3 and Y-Tech’s assistance.

Related posts:

Porsche PIWIS 3 Reviews and FAQs
Porsche PIWIS III Reviews
Porsche piwis 3 new software version updated to V44.800.022 + V38.250
How to Update VXDIAG Porsche PIWIS Tester III Software

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
Porsche PIWIS Programming Issue

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
Porsche PIWIS Programming Issue

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
Porsche PIWIS Programming Issue

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
Porsche PIWIS Programming Issue

This article show a guide on how to use G-scan2

This Post: Porsche PIWIS Programming Issue From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Sovle GM Tech 2 Scanner “HBCC failed and states Ignored” Error
Next: Next: Autel IM608 II Programming for 2022 Honda Passport – All Keys Lost

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2