Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning)

Posted on January 25, 2025 by
PCC1302-Power-Engine

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

PCC1302 PowerCommand  CAN datalink communication has been lost between the generator set control and ECM,therefore event/fault code 2545 becomes active if event/fault code 781 “CAN Data Link Failure” is also active at the ECM.

PCC1302-Power-Engine

Related Contents:

2024 InPower V14.5 Pro V12 Diagnostic Software Free Download

PowerCommand Diagnostic 9 Pin Adapter Cable for InPower

Possible Causes:
1 CAN datalink failure
2 Faulty ECM

Diagnosis and Repair:
1 CAN datalink failure
a Reset the Keyswitch manually.
a Put the generator set control in the OFF position and press the Reset button on the operator panel. This action will clear any shutdown faults and resets the Keyswitch.
b Enable the Keyswitch through the operator panel. Go to Test > Output > Engine > Keyswitch Driver Override Enable, set to Enable.
b Reset the ECM and PCC controls.
a Push the Emergency Stop button in.
b Wait 30 seconds.
c Disconnect the battery terminals from the battery.

d Wait 10-15 seconds.
e Reconnect the battery cables to the battery terminals correctly.
f Pull the Emergency Stop button out.
g Press the Fault Reset button.

c Check the relay that is proving power to the Keyswitch. This relay is normally open, and if faulty, replace.
d Check the terminating resistors. With connectors J11 and J26 removed, measure
resistance between pins J11-19 and J11-20 (60 ohms, is satisfactory).
e Reference the troubleshooting procedure for event/fault code 781 in the engine service manual.

2 Faulty ECM
a After ensuring that the ECM has an adequate B+ supply, connect to the ECM with InPower or Insite in order to determine if it is functioning correctly and can communicate with the PCC controller. Replace the controller if communication to it with InPower is not possible.

Refer to the engine manual for correct threshold values and make the appropriate changes using InPower v14.5 pro.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning)

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning)

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning)

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Toyota Previa MPV Smart Card All Keys Lost Programming Guide
PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning)

Toyota Previa is an MPV produced by Toyota since 1990. It is called Estima (?????) in the Japanese market and Read more

This Post: PCC1302 PowerCommand Code 2545 – Keyswitch Reset Required (Warning) From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: 9 Pin Adapter Cable

Post navigation

Prev: Prev: CGDI K2 Smart Key Tool V3.4.0.0 Update
Next: Next: HITACHI EX5600 Air Conditioner Compressors Removal and Installation Guide

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit
  • How to Solve Caterpillar 24 PID 100-3 Oil Pressure Voltage High?

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2