Here chinaobd2.com show you how to use OPCOM VAXU-COM Program Diesel Pump for Opel.
Preparations:
Newest OPCOM VAUX-COM All Version Free Download
OPCOM Clone
Astra-G / Zafira-A
Donor-car
§ Remove diesel pump from donor-car
§ Attention: You will need donor-car’s Security Code!
Car where donor-pump needs to be installed
§ Install dieselpump in the car
§ Set up communication with ECM
§ Select [Programming]
§ Select [Reset ECU]
§ Enter donor-car’s Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will be resetted, so you can learn it to the new car.
§ Set up communication with Immobilizer module
§ Select [Programming]
§ Enter Security Code of car where you have installed the dieselpump
§ Select [Immobilizer Function Programming]
§ Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Astra-G and Zafira-A can also be installed with a VP44/PSG5 for Y20DTH. These PSG5 units
don’t need to be reset.
Vectra-C / Signum PSG16
Donor-car
§ Remove the diesel pump from donor-car
§ Attention: You will need donor-car’s Security Code!
Car where donor-pump needs to be installed
§ Install diesel pump in the car
§ Set up communication with ECM
§ Select [Programming]
§ Select [Reset ECU]
§ Enter donor-car’s Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will need to be reset, so you can learn it to the new car.
§ Set up communication with CIM module
§ Select [Programming]
§ Enter Security Code of car where you have installed the diesel pump
§ Select [Immobilizer Function Programming]
§ Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Reset immobilizer related controllers
Then, you need to go into each module, for which you have a corresponding fault code stored
in the CIM module (see below), and do a reset/programming cycle with the security code of
the car.
§ IPC Instrument B3925 -00 Wrong Environment Identifier Received IPC
§ REC Rear Electrical Centre B3929 -00 Wrong Environment Identifier
Received REC
§ BCM Body Control Module B3924 -00 Wrong Environment Identifier
Received BCM
§ DDM Driver Door Module B3926 -00 Wrong Environment Identifier Received
DDM
§ PDM Passenger Door Module B3927 -00 Wrong Environment Identifier
Received PDM
After the reset, you need to wait at least 10 seconds with the ignition OFF, to allow the car to
learn the new identifier.
Now select ECM and check programming of:
§ Highspeed CAN bus
§ Variant configuration
§ Tyresize
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat immo Immobilizer OPCOM program
Related Posts
Kobelco ISUZU 4JJ1 P0047 Turbocharger EVRV Control Circuit High Solution
2023.04.2
Can’t read car information with Mercedes BENZ C6 Xentry Diagnosis VCI,how to sol...
2024.01.28
Autel AP200 code scanner is great for BMW F10 5 series
2019.12.13
WinKFP error 211 Solutions
2019.02.24
How to install VIDA2014D on Windows 8.1 / 10 Pro / Core x86 / x64 PC?
2019.03.1
JCB Stage V Engine K4732 Intake Air Temperature Sensor Out of Range
2023.04.6
How to install the software of xprog m ecu programmer?
2019.02.26
Caterpillar ET 2018A Electronic Technician Software Free Download
2019.07.24
How to Sovle issues when programming BCM by tech2
2024.01.28
Xhorse VW MQB Add Key/All Keys Lost Assistant Tools Review
2023.03.15