Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

New Holland T6030 Tractor Control Valve Assemble Guide

Posted on May 20, 2023May 22, 2023 by VCDS
New Holland T6030 Tractor Control Valve Assemble Guide (11)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

After you control valve repairing for New Holland T6030 tractor,it is necessary to assemble it.So here chinaobd2.com show you guide on how to assemble control valve for New Holland T6030 tractor.

 

Related Contents:

CNH DPA5 Adatper

2023 CNH EST 9.8 9.2New Holland Diagnostic Software Free Download

New Holland Agricultural & Construction Parts+Service Manual Free Download

 

Procedures:

1.Prior to inserting control valve spool in housing ensure flats (1) on end of spool are in vertical position as shown, then install the load holding check valve, as described below. Do Not rotate spool after installing load holding valve otherwise damage to spool and load holding valve plunger will occur

New Holland T6030 Tractor Control Valve Assemble Guide (1)

New Holland T6030 Tractor Control Valve Assemble Guide (2)

 

 

Load Holding Check Valve installation

2.Dimensions:

L = Plunger Length

Z = Depth to the Plunger
Y = Depth to the Pilot Ball
B = Pilot Ball diameter ( 4 mm (0.16 in)
X = Gap between the Plunger and the Pilot Ball
NOTE: When the control valve is in the neutral position there must be a gap (X) 0.2

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: New Holland T6030 Tractor Control Valve Assemble Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat gm

Post navigation

Prev: Prev: JCB Tier 4 Air Filter Pressure below Normal Error Solution
Next: Next: ISUZU 4JJ1 Euro 4 N Series Truck EGR Valve Removal and Installation Guide

Related Posts

SmartPRO 5000U-PLUS Programmer Support Unlock Car keys with NXP PCF79XX NCF29XX Serial Chips

SmartPRO 5000U-PLUS Programmer Support Unlock Car keys with NXP PCF79XX NCF29XX ...

2024.01.3

Renault CAN Clip V195 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1

Renault CAN Clip V195 and Consult 3 III For Nissan Professional Diagnostic Tool ...

2020.11.3

BMW FEM BDC Test Platform for FEM/BDC Key, KM reset and ECU Gearbox Programming

BMW FEM BDC Test Platform for FEM/BDC Key, KM reset and ECU Gearbox Programming

2018.12.17

How to Solve CAT ET Error 142 Communications Adapter Error

How to Solve CAT ET Error 142 Communications Adapter Error

2023.04.3

How to connect the Caterpillar ET software to the ECM

How to connect the Caterpillar ET software to the ECM

2024.01.28

JCB StageV Tier4 Air Filter Pressure Sensor Active at Init State

JCB StageV Tier4 Air Filter Pressure Sensor Active at Init State

2023.10.4

Renault Megane IV 2015+ Key Programming by Zed-Full

Renault Megane IV 2015+ Key Programming by Zed-Full

2019.07.24

Best key programmer: Obdstar DP Plus vs Lonsdor K518 vs Autel IM608

Best key programmer: Obdstar DP Plus vs Lonsdor K518 vs Autel IM608

2019.12.16

Scania SDP3 2.44.1 Scania Diagnos & Programmer 3 V2.44.1 Free download

Scania SDP3 2.44.1 Scania Diagnos & Programmer 3 V2.44.1 Free download

2020.06.6

How to make Xentry PassThru work for New Models (Euro5/6, W205, W213, W222)

How to make Xentry PassThru work for New Models (Euro5/6, W205, W213, W222)

2019.03.11

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2