Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

New Holland CX8080 Elevation A0052 Flow Sensor Out of Range Troubleshooting

Posted on January 29, 2024 by VCDS
New Holland CX8080 Elevation A0052 Flow Sensor Out of Range Troubleshooting

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

The information in this Service Bulletin provides the troubleshooting procedure to follow when the alarm code A0052 is visible on the display screen.

 

When the alarm code A0052 occurs, it is no longer possible for the customer to log the yield data of the combine.

The alarms A0052 occurs if the output voltage of the yield sensor is outside the allowable voltage range.

This allowable voltage range depends on whether the unit has a:

Universal Control Module (UCM):

All CR from MY15 onwards with the harvest suite ultra cab.

All CX from MY16 onwards with the harvest suite ultra cab.

Combine Control Module (CCM):

All other combines without the harvest suite ultra cab.

 

 

Related Contents:

2023 CNH EST 9.9 9.2New Holland Diagnostic Software Free Download

CNH DPA5 Diagnostic Kit

CNH eTimGo Offline

 

 

ACTION

PRODUCTION

Not applicable.

 

SERVICE

Unit preparation

NOTE: The four reference points to the unit are the left-hand side, the right-hand side, the front of the unit, and the back of the unit. These reference points apply to someone that faces the direction of travel from a standing position that is behind the unit.

 

WARNING

Avoid injury!

Before you start any work on the unit, prepare the unit according to the following instructions.

Failure to comply could result in death or serious injury.

 

1 Thoroughly clean the area on the unit that pertains to the service instructions for this Service

Bulletin.

2 Park the unit on a hard, level surface.

3 Apply the parking brake.

4 Completely lower any attachments to the ground.

5 Relieve all of the hydraulic system pressure.

6 Shut down the engine.

7 Follow any specific instructions that pertain to the unit within the service instructions as necessary.

 

Service instruction CX and CR combines with the UCM controller:

NOTE: When troubleshooting an A-0052 alarm code on a combine with a UCM, it is important to first verify the part number of the yield sensor. The part number of the yield sensor will determine the specific troubleshooting steps to follow.

The part number of the yield sensor is on a white sticker on the top of each yield sensor.

Specific information for the yield sensor:

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: New Holland CX8080 Elevation A0052 Flow Sensor Out of Range Troubleshooting From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat CNH DPA5 key ops

Post navigation

Prev: Prev: How to add 2018 Dodge Challenger with Autel IM608 Pro
Next: Next: Scania Truck Auxiliary Heater System Insufficient Voltage Solution

Related Posts

Latest Version VCM5 VCM 5 IDS5 for Ford and Mazda OBD2 Diagnostic Tool

Latest Version VCM5 VCM 5 IDS5 for Ford and Mazda OBD2 Diagnostic Tool

2018.12.26

Whats the Different between XTOOL X100 PAD3 and PS90

Whats the Different between XTOOL X100 PAD3 and PS90

2024.01.28

How to Update BMW ICOM/ICOM NEXT Firmware by Manual

How to Update BMW ICOM/ICOM NEXT Firmware by Manual

2024.06.15

How Use BMW ISTA-P Generate BMW IBAC Enable Codes

How Use BMW ISTA-P Generate BMW IBAC Enable Codes

2019.07.24

Update!How to Use Yanhua ACDP Renew BMW CAS1

Update!How to Use Yanhua ACDP Renew BMW CAS1

2019.03.8

WinOLS Tune ECU Map for Volvo 850 T5 Motronic 4.3 ECU

WinOLS Tune ECU Map for Volvo 850 T5 Motronic 4.3 ECU

2019.02.24

Five reasons why programmer chip programming is unstable

Five reasons why programmer chip programming is unstable

2023.06.4

US$157.00-2019 Latest Version X-PROG Box ECU Programmer Shipping from Uzbekistan

US$157.00-2019 Latest Version X-PROG Box ECU Programmer Shipping from Uzbekistan

2019.02.27

Usermanual:Autek IKey820 Active and Update Guide

Usermanual:Autek IKey820 Active and Update Guide

2023.06.10

Toyota Servo Motor Initialization by Launch X431

Toyota Servo Motor Initialization by Launch X431

2019.02.27

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Scania Truck Direction Indicator Front Right CUV 5 Trouble Repair
  • How to Solve CAT C9 Engine 8 Volt Supply Voltage High Problem
  • How to Replace HV Battery ECU for HINO Truck J05E Engine
  • Scania Truck CAN Communicatinon Fault Engine Control Unit Error Solution
  • Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2