Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout

Posted on February 15, 2025 by
Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (9)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout

Vehicles: Monza, Kadett and Ipanema, from 91 to 96.

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (1)

More ECU PINOUT Components:

ECU Modules Repair Pinpout & Components

Main components

1 Injector drive;

2 16156085 – Fuel pump relay drive;

3 34993 – Stepper motor drive;

4 Delco 196 E – 16045980 – PF relay – Injection light – Flight computer – V2 fan;

5 Processor;

6 Delco 196 E – 16045980 – V1 Fan – Heating relay collector – Ascending light – A / C relay;

7 34992 – 5V regulator;

8 NTC;

9 Processor;

10 Cristal – Clock;

11 Eprom, 27C128

Technical specifications

Special features

. Multec 700 exchanges are all the same, the difference is only in the mencal (Calibration Memory).

. Drive Beak – Commercial – IRF 540 or IRFZ34N.

Common defects

Failure in the fan relay drive;

Bad contact at the injector secondary drive terminals and pump, causing failure when moving the ECU. Necessary to resold the terminals.

Note:

For the injector to pulse, it is necessary to jump the terminals D9 and D10. Doing this, passes the earthing of the D9 to D10, that is, for the injector to work is pin D10 must be grounded.

ECUs are the same, what changes is the month.

Injector drive – 3 pins

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (2)

This component is a  NPN transistor, with ferrite on the coupling (firing). This washer aims to eliminate electromagnetic interference.

Note: Note that the trigger has a range of 10 volts.

Secondary drive – Injector – Fuel pump

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (3)

Processor

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (4)

Mencal

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (5)

Regulator 5 volts – 34992 – 15 pins

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (6)

Delco 169 E 1 and 2

Delco 169 E – 1 – PF Relay – Injection light – Computer board – V2 fan – 15 pins

In this component the input (trigger) is negative and its out (out) is also negative.

Delco 169 E – 2 – V1 fan – collector heater relay

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (7)

Stepper motor drive – 34993 – 9 pins

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (8)

Note: When the ignition is switched off, the ECU starts the engine step, that is, to test the drive just turn on and off the ignition. And test with the oscilloscope.

Pump relay drive and Injector drive

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout (9)

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: PADFLASH VS FOXFLASH ECU & TCU Programmer
Next: Next: PADFLASH VS FOXFLASH ECU & TCU Programmer

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua ACDP2 Program BMW G Chassis BDC2 All Keys Lost on Bench
  • Scania Truck ALM 000800 Interrupted LIN Communicatin Siren
  • BMW G Series BDC2 Module Virgin and Replacement by APPRO2
  • CG FC200 V1.2.9.2 Update: BMW Coolant Temperature Setting Added
  • Scania Truck ALM 000463 Motion and Inclination Detector,Calibration Fault

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2