Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Kubota U48-4 Piston Pump Air Bleeding Procedure

Posted on July 28, 2023 by
Kubota U48-4 Piston Pump Air Bleeding Procedure (3)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to perform piston pump air bleeding for Kubota U48-4 and U55-4 excavator.

 

Related Contetns:

Kubota Diagmaster 22.08.01 free download
Kubota DST-i Diagnostic Adapter

Kubota EPC Spare Parts Catalogue 2021.06 Download

 

Piston Pump Air Bleeding Procedure
When disassembling hydraulic equipment and replacing hoses,etc., or after changing the hydraulic fluid and using the vacuum pump, before operating the machine, be sure to carry out air bleeding to prevent pump scorching and cavitation.

1.After operating, with the engine stopped, remove the hose at the top of the pump from its clamp.
2.Insert a hexagonal plug, pinch the black plastic lock section, and pull out the hexagonal plug.
3.Drape the hose on the front of the weight, and leave for 30 seconds.
4.Fit a hexagonal plug to the hose, start and idle the engine, and check whether there is any cavitation noise from the pump.
5.Repeat operations in 2. 3. 4 until pump cavitation noise subsides.
6.When cavitation noise subsides, raise the engine speed to 1500 rpm, slowly operated the arm and check whether cavitation noise is emitted. (Make sure there is no relief when operating the arm)
7.If there is no cavitation noise, raise the engine speed to 2000 rpm, slowly operate the arm, and check again for cavitation noise. If cavitation noise is emitted, stop the engine and carry out 2. 3.
8.If there is no cavitation noise in step 7, raise the engine speed to maximum rpm, slowly operate the aim, and check again for cavitation noise. If cavitation noise is emitted, stop the engine and carry out 2. 3. (Make sure there is no relief when operating the arm)
9.If there was no cavitation noise when performing step 8, air bleeding is finished. Clamp the air bleed hose in its original position.

Kubota U48-4 Piston Pump Air Bleeding Procedure (1)

Kubota U48-4 Piston Pump Air Bleeding Procedure (2)

Kubota U48-4 Piston Pump Air Bleeding Procedure (3)

 

(1) Air bleed hose
(2) Hexagonal plug
(3) Lock section

 

More repair case for Kubota,please refer to:Kubota Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Kubota U48-4 Piston Pump Air Bleeding Procedure From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
Next: Next: How to Use JCB ServiceMaster 4 Vehicle Setup Data Tool Function

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution
  • Use Xhorse MLB Tool MQB48 Adapter and Key Tool Plus in 2 Methods
  • Yanhua ACDP Module 38 Add BMW G Chassis BDC2 Key on Bench
  • Top 5 BMW G-Chassis BDC2 Module Key Add Tools Review

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2