Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Kubota L3301 L3901 Excavator Readjustment of Relief Valve

Posted on February 11, 2025 by
Kubota L3301 L3901 Excavator Readjustment of Relief Valve (5)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Here is the procedures for Kubota L3301 L3901 L4701 excavator relief valve readjustment.

Related Contents:

2024 Kubota Takeuchi Diagmaster v24.01.06 Software Free Download

Kubota EPC Spare Parts Catalogue 2021.06 Download

Kubota DST-I Diagnostic Tool

(When the HST does not work due to its loose hexagon socket head screw)
IMPORTANT
• The KUBOTA does not recommend the readjustment of relief valve. And KUBOTA will recommend the exhaust with genuine parts.
• As the HST may be damaged if the pressure is set to higher by mistake, be careful when adjusting it.
NOTE
• The relief pressure is set in between 33.4 to 36.2 MPa (340 to 370 kgf/cm2, 4840 to 5260 psi) when shipped from the factory. But, for the purpose of after-sales services, as it is impossible to reset the pressure precisely as set in the factory, its setting range is defined as a slightly wider range
between 31.4 to 35.3 MPa (320 to 360 kgf/cm2, 4560 to 5120 psi).

1 Measure the pre-adjustment distance “A”.

Kubota L3301 L3901 Excavator Readjustment of Relief Valve (1)
2 Compress the spring of the relief valve with a relief valve assembling tool (3).

Kubota L3301 L3901 Excavator Readjustment of Relief Valve (2)
3 Then, find the distance “A” by turning the poppet (4) with a screwdriver.

Reference: The distance “A” changes by about 1.5 mm (0.02 in.) per one turn of the poppet (4).
4 Repeat the same operation a few times to find the distance “A” as it is difficult to acquire at the first time.

Kubota L3301 L3901 Excavator Readjustment of Relief Valve (3)
5 After finding the distance “A”, hold the setscrew (6) to a vice and fasten the hexagon socket head screw (2) with specified torque.

Kubota L3301 L3901 Excavator Readjustment of Relief Valve (4)
On this occasion, use a copper plate, etc. for the vice jaws not to damage the setscrew (6).
6 Install the relief valve in the HST.
7 Check the relief pressure as indicated in page 3-S14.The distance “A” is for refresh only. Make sure to check the relief pressure after readjustment.
8 If the relief pressure does not fall within the readjustment pressure range, repeat the processes of the above item 1 onward.
Reference: The pressure changes by 1.5 MPa (15 kgf/cm2,210 psi) per 0.1 mm (0.004 in.) in distance “A”

Kubota L3301 L3901 Excavator Readjustment of Relief Valve (5)

More repair case for Kubota,please refer to:Kubota Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Kubota L3301 L3901 Excavator Readjustment of Relief Valve From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: OBDSTAR DC706 Repair 2016 Honda Civic Keihin Idle Speed
Next: Next: How to Use Xhorse VVDI MLB Tool and MQB48 Adapter?

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2