Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions

Posted on April 4, 2023 by

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Several days ago,we learn a instruction on how to solve JCB excavator K0141 oil pressure sensor voltage above normal or open circuit.Now here another situation on how to solve JCB K0141 oil pressure sensor voltage below normal.More repair case for JCB,please refer to:JCB Trouble Repair

 

Related Content:

WinEEM4s JCB Service Tool 2.7.2 2.6.1 Free Download

 

The measured oil pressure signal is below the normal operating range (< 0,1 V).

Possible causes are:

The oil pressure sensor wiring is defective. (Shorted to ground.)

The oil pressure sensor power supply is not correct.

The oil pressure sensor is defective.

 

Reaction in EEM

The FC is stored and the oil pressure warning lamp is activated. Engine power will be reduced (Degradation Level 1). The CAN message indicates active fault. The engine protection functions that depend on oil pressure are not active.

NOTE: The engine oil pressure protection is not active. The engine may be damaged, if the oil pressure is too low.

 

Solution

First save the error log and then erase it. Restart the ECU after erasing the error log. If the fault occurs again during the next driving cycle, check the following paths:

Check the oil pressure sensor wiring, the connectors and the contact surfaces of the connector pins (possible oxidation).

Check the 5 V power supply to the sensor.

Check the operation with another oil pressure sensor to see if the oil pressure sensor is defective.

(Visited 42 times, 1 visits today)

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions

This article show a guide on how to use G-scan2

This Post: JCB K0141 Oil Pressure Sensor Voltage Below Normal Solutions From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Restore/Reset Airbag Module for Hyundai by GPROG Lite Programmer
Next: Next: How to Use MUT-III Diagnostic Software Actuator Test Function

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2