Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

JCB 3CX/4CX/5CX Loader Hand Throttle Position Sensor Service Steps

Posted on August 23, 2024 by
JCB 3CX4CX5CX Loader Hand Throttle Position Sensor Service Steps (5)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Here is the illustration show the service steps for JCB Backhoe Loaders 3CX/4CX/5CX hand throttle position sensor.

 

Related Contents:

WinEEM4s JCB Service Tool 2.7.2 2.6.1 Free Download

2024 JCB ServiceMaster 4 v24.6.2 Free Download for Win 10 Win11

2017 JCB Parts Plus+ and Repair Service Manual Free Download

 

 

Function

Determines hand throttle position set by the operator.

 

Location

On Backhoe Loader machines, the hand throttle position sensor is mounted under the front console.

JCB 3CX4CX5CX Loader Hand Throttle Position Sensor Service Steps (1)

 

Signal

Analogue voltage between 0 volts and 5 volts.  Voltage output proportional to throttle lever position. Two throttle tracks are used to ensure safety of the operator in the case of throttle malfunction.

 

JCB 3CX4CX5CX Loader Hand Throttle Position Sensor Service Steps (2) JCB 3CX4CX5CX Loader Hand Throttle Position Sensor Service Steps (3)

 

Internal Electrical Schematic

JCB 3CX4CX5CX Loader Hand Throttle Position Sensor Service Steps (4)

 

Testing

Important: Use the multi-meter on the harness connector pins. DO NOT use the meter on the ECU pins. (SN0011)

1 Disconnect the sensor.

2 Switch the ignition ON.

3 Check supply voltage is 5 volts (pins 1 and 4). Connector pin 3 and 6 should read ground (0 volts).

4 If voltages are incorrect, check harness for continuity and ground conditions, check ECU pins for evidence of contamination or corrosion.

5 Measure signal voltage from the throttle position sensor when the throttle is at idle.

a)Pin 2 = 1.0 to 1.2 volts.

b)Pin 5 = 0.4 to 0.6 volts.

6 Measure signal voltage when throttle is fully depressed.

a)Pin 2

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: JCB 3CX/4CX/5CX Loader Hand Throttle Position Sensor Service Steps From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: CLAAS LEXION 8900 Perkins 2206 D-E13TA engine Oil and Oil Filter Changing Guide
Next: Next: QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2