Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

Posted on December 24, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials:

If you reading and programming the original car, the details steps just check the VVDI Prog Operation Guide.

If your car is 9S12DG 128 CPU, the operation steps are as follows:

Read out the EEPROM data, atttention! pls save the data! in case of any wrong operation

Put the read EEPROM file into the folder J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

Then double-click the EEPROM Converter application,

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

and see that the original 2K file becomes 4K, the conversion is successful.

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

After runing the sytem, the file to be 4K, then the programming succeed

Note: Can only double click one time, do not repeat.If the double-click run is unsuccessful, or no 4K file appears, then right-key to run the program in administrator mode.

Connect flashing wire and write the converted EEPROM file.Attention: simulator is a 256 chip then choose  J518 (2010) (0L01Y) required.

Each board all with ep data and FLSAH data, so usually you just need to write EP data.If not, you can write  the EP data from your car with the FLASH data in the instruction.

If car is 9S12DG 256 CPU, the operation steps are as follows:

Read out and save the original car data, and write it directly to the simulator.

wiring method

VVDI burning line: where: red (thick) =VCC black (thick) =GND yellow =RST purple =BKGD green =XCLKS White =CLK black (fine) =GND-C

without horn

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

With horn: wiring according to the silk print in the board ,same as board wihtout horn

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

Buy our special burning line, with speakers can be no welding burning, directly into the 20pin port.

Notice:

The simulator is burned after the test, preferably on the car.

In the test platform test, it is necessary to pay attention to check the wiring of 20Pin port. Some of the platform wiring harness production problems, which will conflict with our burning interface, which may lead to chip damage.

Error wiring: 10 (red) should recover after 20 (blue) or as shown in the figure.

J518 ELV Module Emulator 9S12DG 128/256 CPU Operation TutorialsJ518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials

Learn more: https://www.chinaobd2.com/vp-j518-elv-module-emulator-work-for-vvdi.html

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: J518 ELV Module Emulator 9S12DG 128/256 CPU Operation Tutorials From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: SVCI 2020 V12 Software Free Download
Next: Next: CG FC-200 V1.0.7.0 Update and Download

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • ECUDESK Software Latest ECU Support List (2025.05)
  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2