Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

ISUZU F-Series 6.7 Truck Shift Cable Adjustment/Replacement Guide

Posted on August 31, 2024 by

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to adjust and replace shift cable for ISUZU F-series truck.

 

Inspection Procedure

1  Turn the ignition to OFF.

2  Block the wheels.

3 Confirm that full forward travel P (park) position can be obtained.

4  Press shifter lock release button.

5 With the transmission shift detent controlling the shift lever position, place shift lever indicator into N (neutral) position.

6 Observe shift lever indicator position. If red indicator band is centered in the N position, no further adjustment is required.

 

Adjustment Procedure

Note: The adjustment for the shift cable is performed at the shift housing end of the cable. The cable is held in place by a clip and washer.

1 Remove the fasteners securing the shift control housing to the shift control, and position the control housing out of the way.

2 Disconnect the shift cable from the shift control by removing the pin and washer then move the cable end off the pivot pin on the shift housing.

ISUZU F-Series 6.7 Truck Shift Cable AdjustmentReplacement Guide (1)

 

3 At the transmission rotate the transmission selector shaft lever to the Neutral (N) position.

4 Move the shift lever to the neutral detent position. Note: You may need to manually override BTSI to move the shift lever.

5 While holding the cable end eye adjust the turnbuckle so that the cable end eye fits freely over the pivot pin on the shift control.

6 Install the washer and clip.

7 Tighten both jam nuts on the adjusting turnbuckle.

ISUZU F-Series 6.7 Truck Shift Cable AdjustmentReplacement Guide (2)

Note: The backlash is defined as the amount of shift lever travel measured at the PRNDL lens before the transmission selector starts to move.

8 Verify the backlash of the shift lever is less than 2mm when the lever is pushed from the N towards the R direction with the shift button depressed fully.

9 Verify the backlash of the shift lever is less than 4mm when the lever is pushed from the N towards the D direction with the shift button depressed fully.

 

 

Shift Cable Replacement

Removal Procedure

1 Turn the ignition to OFF.

2  Block the wheels.

3  Move the shift lever to the neutral position.

4  Remove the fasteners securing the shift control housing to the shift control, and position the control housing out of the way.

5 Remove the fasteners and clips securing the shift cable to the shift control.

 

ISUZU F-Series 6.7 Truck Shift Cable AdjustmentReplacement Guide (3)

6 Remove the cable clip (2), clevis pin (4), and washer (3) securing the shift cable (1) to the transmission shift lever.

ISUZU F-Series 6.7 Truck Shift Cable AdjustmentReplacement Guide (4)

7  Note the positions of the clamps securing the shift cable to the vehicle. Remove the bolts and clamps (1) securing the shift cable (2) to the frame rail and brackets.

8  Remove the grommet securing the shift cable to the cab.

9  Remove the shift cable.

 

Installation Procedure

ISUZU F-Series 6.7 Truck Shift Cable AdjustmentReplacement Guide (5)

1  Position the new shift cable in the original position.

Notice:

  • Ensure the shift control lever and the transmission shift lever are in the mechanical neutral position. Mechanical neutral at the transmission is 2 clicks away from the bottom most position.
  • Refer to Fastener Notice .

2 Install the bolts and the clamps (1) in order to secure the shift cable (2) to the frame rail and brackets.

3 Install the grommet securing the shift cable to the cab.

Tighten the bolts to 20 N-m (15 lb ft).

4  Install the fasteners and clips in order to secure the shift cable to the shift control.

Tighten the nuts to 22 N-m (16 lb ft).

5  Adjust the shift cable. Refer to Shift Cable Adjustment .

6  Install the fasteners in order to secure the shift control housing to the shift control.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: ISUZU F-Series 6.7 Truck Shift Cable Adjustment/Replacement Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How Use JPRO Diagnostic to Do DPF Service Regeneration
Next: Next: How to Solve Doosan Excavator P02E2 Short Circuit to Ground

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution
  • Use Xhorse MLB Tool MQB48 Adapter and Key Tool Plus in 2 Methods
  • Yanhua ACDP Module 38 Add BMW G Chassis BDC2 Key on Bench
  • Top 5 BMW G-Chassis BDC2 Module Key Add Tools Review

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2