Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Use Ktag to Clone ECU for BMW 5 Series MEVD17

Posted on December 7, 2024December 8, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

It is necessary to clone ECU data when you need replace a used ECU for BMW,you need to read out EEPROM and flash data from old ECU.Then write the data into the new/used ECM to replace.This is a step by step guide on how to use KTAG programmer to clone ECU data for BMW 5 series BOSCH MEVD17.

https://www.chinaobd2.com/wholesale/ktag-v7020-firmware-eu-version-online-version-5169.html

How to Use Ktag to Clone ECU for BMW 5 Series MEVD17

Preparations:

KESS V2 KTAG K-Suite Software Download & Installation

PROCEDURES:

Step 1:

Run KTAG software then select vehicle models

 

Step 2:

Recommendation

Remove the ECU from the vehicle;
Open the ECU, taking care in not damaging the parts inside;
Reconnect the ECU to the vehicle and start the engine, in order to make sure that it is still workin and has not been damaged in the opening;

Remove again the ECU from the vehicle;
Select the right plug-in;
Always make a backup copy of the ECU before Reading and / or Writing.

Instructions

Connect to the ECU according to the pinout provided for each model (click here for connection instructions);

Select the right plug-in;
Make reading and programming (click here for further instructions).

 

Step 3:

Follow the instruction to find correct ECM models version

 

Step 4:

After then check ECU diagram connection for DME GPT

 

Step 5:

Select 679,if communication failed from ECU,then try 678 or 719 protocals

 

Step 6:

Select untick “Backup”

Select EEPROM and MAPS (flash data)

Click read to read out data

 

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Use Ktag to Clone ECU for BMW 5 Series MEVD17 From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat EEPROM EPROM KESS KTAG program wholesale

Post navigation

Prev: Prev: How to Use Cat ET 2024A to Perform Fuel Rail Pressure Test
Next: Next: Piwis 3 VS Piwis 4, what is the best interface?

Related Posts

LISHI HY17 2 in 1 Auto Pick and Decoder For HYUNDAI/KIA

LISHI HY17 2 in 1 Auto Pick and Decoder For HYUNDAI/KIA

2018.12.17

HINO Trucks EPC Electronic Parts Catalog 2016 2015 Free Download

HINO Trucks EPC Electronic Parts Catalog 2016 2015 Free Download

2019.07.24

V2.13 FW V6.070 KTAG K-TAG ECU Programming Tool Master Version with Renew Button Unlimited Token

V2.13 FW V6.070 KTAG K-TAG ECU Programming Tool Master Version with Renew Button...

2018.12.17

How to Cheaply Add Horsepower with an ECM Flash

How to Cheaply Add Horsepower with an ECM Flash

2024.01.28

Chinaobd2.com Black Friday Offers: Finest Value & Free Reward

Chinaobd2.com Black Friday Offers: Finest Value & Free Reward

2024.12.24

VCP System Program BCM PQx5 for VW Golf,Polo,Ibiza

VCP System Program BCM PQx5 for VW Golf,Polo,Ibiza

2019.07.22

New Arrival T300 T300+ Key Programmer English Version Black

New Arrival T300 T300+ Key Programmer English Version Black

2018.12.25

BMW Carly Disable Headlight Bulbs Flickering

BMW Carly Disable Headlight Bulbs Flickering

2019.02.24

Two Ways to Read MQB NEC35xx IMMO with VVDI Key Tool Plus/VVDI2+VVDI Prog

Two Ways to Read MQB NEC35xx IMMO with VVDI Key Tool Plus/VVDI2+VVDI Prog

2023.04.1

How to Setup CAT ET Work with Nexiq USB Link2

How to Setup CAT ET Work with Nexiq USB Link2

2023.05.13

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Deutz EMR3 Engine 59 /701/Dummy1CD Error Solution
  • Scania Truck Direction Indicator Front Right CUV 5 Trouble Repair
  • How to Solve CAT C9 Engine 8 Volt Supply Voltage High Problem
  • How to Replace HV Battery ECU for HINO Truck J05E Engine
  • Scania Truck CAN Communicatinon Fault Engine Control Unit Error Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2