Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Use DMS-5 to Calibrate Swash Plate Angle

Posted on May 5, 2023May 5, 2023 by VCDS
How-to-Use-DMS-5-to-Calibrate-Swash-Plate-Angle-7

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to use DMS-5 diagnostic software to calibrate swash plate angle for Doosan excavator.

 

Related Contents:

Doosan Data Monitoring System DMS-5 DMS-3 Free Download

Daios Doosan EPC Excavator Part Catalog 2017 Download & Installation

 

Procedures:

Swash Plate Angle Calibration

How-to-Use-DMS-5-to-Calibrate-Swash-Plate-Angle-1

<Pump Swash plate angle sensor calibration concept>
1. In the case of VBO, the flow rate of the pump is controlled based on the swash plate angle sensor value, so the
sensor value must be measured at the maximum/minimum of the swash plate angle and calibration to the Software
reference value for accurate flow control.
2. That is, by measuring the swash plate angle sensor output(voltage) when the pump is at the maximum/minimum
position to calibrate the maximum/minimum swash plate angle value. 3.
3. For example, theoretically, the sensor output voltage at the maximum/minimum swash plates is at 4.5/0.5V, but if
the actual sensor value is 4.4/0.4V, it will be calibrated at 4.4V and the minimum at 0.4V.

<Caution>
1. The green light meaning of the displayed value is an indication that the tolerance for mounting the pump angle
sensor is within range, meaning no calibration is required. It is recommended that the measurements be calibration for
precise control.
2. That is, click

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Use DMS-5 to Calibrate Swash Plate Angle From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat diagnostic software

Post navigation

Prev: Prev: HITACHI ZX-7 Excavator GSM Removal Guide
Next: Next: JCB 3CX 4CX Loader Servo Pressure Supply Valve Dismantling and Assembly

Related Posts

How to Setup Communication for Doosan e-Doctor EDIA Software

How to Setup Communication for Doosan e-Doctor EDIA Software

2024.02.25

How to Remove and Calibrate Primary Hydraulic Power System for New Holland

How to Remove and Calibrate Primary Hydraulic Power System for New Holland

2024.01.28

LAUNCH X431 CR3001 OBD 2 CAR Code Reader Support Full OBDII/EOBD Launch Creader 3001 CR3001 Auto Scanner PK AD310 NL100 ELM327

LAUNCH X431 CR3001 OBD 2 CAR Code Reader Support Full OBDII/EOBD Launch Creader ...

2018.12.26

SsangYong EPC Parts Catalog Free Download

SsangYong EPC Parts Catalog Free Download

2019.07.26

Toyota Lexus ES250 Tire Pressure Sensor Program by Launch X431

Toyota Lexus ES250 Tire Pressure Sensor Program by Launch X431

2020.07.18

BMW Rheigold ISTA Usermanual Download

BMW Rheigold ISTA Usermanual Download

2019.02.24

How to Associate microPODs to Service Technicians at CJDR + FA Dealerships

How to Associate microPODs to Service Technicians at CJDR + FA Dealerships

2019.06.17

PACCAR Truck Rear Drive Axle Oil Temperature Gauge Inoperative Repair

PACCAR Truck Rear Drive Axle Oil Temperature Gauge Inoperative Repair

2023.04.3

BMW 35160 & 35080 EEPROM Odometer Correction By Yanhua 35xx Emulator

BMW 35160 & 35080 EEPROM Odometer Correction By Yanhua 35xx Emulator

2019.02.24

Carprog Read MC68HC05 Processor Guide

Carprog Read MC68HC05 Processor Guide

2019.02.24

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Scania Truck Direction Indicator Front Right CUV 5 Trouble Repair
  • How to Solve CAT C9 Engine 8 Volt Supply Voltage High Problem
  • How to Replace HV Battery ECU for HINO Truck J05E Engine
  • Scania Truck CAN Communicatinon Fault Engine Control Unit Error Solution
  • Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2