Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection

Posted on July 23, 2023 by
How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection (3)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

New CAT Adapter 478-0235 support Enthernet connection,but you need setup Ethernet connection type on CAT ET software firstly.

 

Preparations:

CAT ET 2023A

CAT Adapter 3 478-0235

 

ECMs capable of Ethernet flashing will also detect over J1939 via Cat Communication Adapter.
1.From the Communications tab (1) of the Preferences dialog, select Ethernet Direct Connection (2).
2.Ensure that the appropriate Ethernet adapter has been selected (3). Ethernet adapter descriptions will vary by manufacturer.
Note: If the Ethernet adapter does not appear as a selection, check the Device Manager to ensure Ethernet adapter drivers haves been installed and the device is working properly.

How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection (1)

Physical Network Connectivity
1.Using Caterpillar cable part number 305-5528, make sure the deutsch-style connector is plugged securely into Ethernet Service Port on the machine and RJ45 connector end is plugged securely into the network adapter slot on the PC.

2.Verify that the status lights on the PC Ethernet port are illuminated. Generally, there are two lights: one light is continuously illuminated and the other light flashes according to network activity. On some ports there may be only a single light that flashes with network activity.

a.If no status light is illuminated, there is a physical wiring problem between the ECM and the PC. Verify continuity of the cable and/or substitute a different cable.
b.If a status light is red, consult the documentation for the network adapter. The lights are typically green, amber, orange, or yellow under normal conditions.

How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection (2)

How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection (3)

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Setup CAT ET Software for Cat Adapter 3 Ethernet Connection From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Reset Application Controller 1100 for John Deere 9620R Tractor
Next: Next: New Holland CX8000 CX7000 Series Battery Service Manual

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution
  • Use Xhorse MLB Tool MQB48 Adapter and Key Tool Plus in 2 Methods
  • Yanhua ACDP Module 38 Add BMW G Chassis BDC2 Key on Bench

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2