Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Reset All ECU

Posted on April 3, 2023 by
How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-7

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction will show you guide on how to reset all the issues and control modules for your car or truck. This will reset the idol and the shifting adaptation and will help that is you learn all new values from scratch in the computer. Our car is 2005 FORD Explorer , but this should be work for most vehicles except some specific vehicle.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-1

 

Procedure

Prepare a jumper wire, remove the negative battery cable

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-2

Put a rag and cover negative for isolate it, then put one end of jumper wire on the negative, the other end on the positive.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-3

Leave it for a while, it completely drains all the charge from all the issues. It stays static and the positive circuits will drain into the negative and down to the ground.

After twenty minutes, remove the jumper cable and rag, then put the negative back on.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-4

Turn on ignition and leave it on for about ten to fifteen seconds. Let the ECU relearn that new values.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-5

Turn the key off and turn the key on, cycle the key. Then turn the car on.

Leave it running for about five minute. Turn all the accessories off.

Idling perfectly at about 750-800 rpms.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-6

Go through the gears, from P-R-N-D-3-2-1, 1-2-3-N-R-P twice.

How-to-Reset-All-ECUs-and-Control-Modules-in-2005-FORD-Explorer-7

For the next few months you want to drive the car easily, the shifting adaptation learns how you drive and all the values would be properly learned by the ECU

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to Reset All ECU

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to Reset All ECU

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to Reset All ECU

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
How to Reset All ECU

This article show a guide on how to use G-scan2

This Post: How to Reset All ECU From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Replace Steering Angle Sensor for Still Steds iGo Neo Forklift
Next: Next: How to Maintenance Kubota V3800 Diesel Engine Every 1000 Hours

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit
  • How to Solve Caterpillar 24 PID 100-3 Oil Pressure Voltage High?

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2