Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to replace Benz W203 Light Control Switch Module

Posted on February 24, 2019 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Sometime if you find there is trouble with your Benz light switches,it remind you that car light switch module going bad.So in this article you will get skills about How to replace Benz W203 Light Switch Module.

 

This method is also applied for Mercedes-Benz Model:

C230, C280, C350, C240, C320.(2001-2007)

 

Procedures of Light Control Module replacement:

Step 1:You will need to open the driver side door to give you access to the T20 screw located under the parking brake handle (red arrow) as well as remove the access panel on the end of the dash (yellow arrow).

How to replace Benz W203 Light Control Switch Module

Step 2:Begin by pulling the brake handle out. This will give you access to a single T20 Torx screw located under the handle. Unscrew this and remove it (red arrow).

How to replace Benz W203 Light Control Switch Module

Step 3:Remove the access panel at the end of the dash. It just pulls straight off.

How to replace Benz W203 Light Control Switch Module

Step 4:Look inside and you will see one metal clip holding the module in place (yellow arrow). There is another one on the other side of the unit.

How to replace Benz W203 Light Control Switch Module

Step 5:Compress the clip and push the unit forward (yellow arrow) until it releases from the dash.

How to replace Benz W203 Light Control Switch Module

Step 6:Turn the module over and release the wiring harness. Push in the clip and slide the arm on the connection down (red arrow), releasing it from the module.

How to replace Benz W203 Light Control Switch Module

Step 7:Installation is the reverse of removal.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to replace Benz W203 Light Control Switch Module

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to replace Benz W203 Light Control Switch Module

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to replace Benz W203 Light Control Switch Module

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
How to replace Benz W203 Light Control Switch Module

This article show a guide on how to use G-scan2

This Post: How to replace Benz W203 Light Control Switch Module From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Disable BMW E92
Next: Next: Camry altise replacing a tail light guid

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2