Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Replace and Program New BCM for Opel Corsa-D

Posted on March 21, 2019March 21, 2019 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This mini post show how to the procedures of replace and program new BCM for Opel Corsa-D.

How to Replace and Program New BCM for Opel Corsa-D

Note:When you are programming,you need to use OPCOM software to perform,download here:Newest OPCOM VAUX-COM All Version Free Download

Preparations:

Before you replace the BCM make a note:

  • Security Code
  • V.I.N.
  • Mechanical key number (MKN)
  • CAN-High configuration
  • CAN-LOW configuration
  • CAN-Middle configuration
  • Perform a complete diagnostic test and store the results
  • Make sure that the V.I.N. matches the vehicle and other installed

Install the new BCM

  • Perform CAN-High, Low and Middle configuration settings
  • Program Immobilizer function, select BCM installation
  • Program V.I.N. and mechanical key number in the new BCM
  • Match all available keys to the BCM

Perform a reset of these controllers:

o IPC

o BCM

o SDM

Switch off ignition and wait at least 15 seconds

Program Security Code in these controllers:

o IPC

o BCM

o SDM

The new BCM has now been programmed to the car.

Run another diagnostic-test. Clear remaining DTC’s and check if all is working fine.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
Original Handy Baby 2 II Key Programmer Hand-held Car Key Copy Key Programmer for 4D/46/48 Chips
How to Replace and Program New BCM for Opel Corsa-D

Handy Baby 2 II Key Programmer Hand-held Car Key Copy Key Programmer for 4D/46/48 ChipsNote: Language: English, SpanishThis Device can't work together Read more

Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1
Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1

Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1 Descriptions of Consult 3 Read more

Super VAG K+CAN V4.6 With Multi Language
Super VAG K+CAN V4.6 With Multi Language

Super VAG K+CAN V4.6 Top 3 Reasons To Get Super VAG: Software Version: V4.6Supported Languages: English/ Spanish/ Italian/ Portuguese/ GreekUDS Protocol Read more

Opcom OP-Com 2014 V Can OBD2 Opel Firmware V1.45 with PIC18F458 Chip Support Firmware Update
Opcom OP-Com 2014 V Can OBD2 Opel Firmware V1.45 with PIC18F458 Chip Support Firmware Update

Opcom OP-Com 2014 V Can OBD2 Opel Firmware V1.45 with PIC18F458 chipSoftware / Firmware Version: Software Version: 120309aFirmware version: 1.45 OPCOM 2014 Function, Workable Read more

This Post: How to Replace and Program New BCM for Opel Corsa-D From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: Immobilizer key OPCOM program

Post navigation

Prev: Prev: Launch X431 Reset Audi A6L Service Lamp and Service Interval Set
Next: Next: How to Configure MB SDconnect WLAN Router

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2