Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission

Posted on September 22, 2023 by
How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (6)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to remove shift bar housing for Eaton heavy duty transmission.

 

Related Contents:

2022 EATON ServiceRanger 4.10 and 4.2 + Activator Free Download

 

Special Instructions
Before removing the Shift Bar Housing, the Air Lines must be disconnected.
For models equipped with an Oil Pump and/or Cooler Assemblies, make sure to disconnect the oil line connected to the Shift Bar Housing.
There are three (3) sizes of Cap Screws. The 1 1/2? Cap Screws are used with the Lifting Eyes. The 1 1/4? are used on all other locations except the left front corner at the Roll Pin location. This Cap Screw is 1 3/4?.
Be careful when removing the Shift Bar Housing to prevent damaging the Oil Tube with the Shift Yokes.

 

Procedure
1.From the Shift Bar Housing, remove the two Shift Bar Retaining Cap Screws securing the Oil Cooler. Remove Oil Cooler and set aside.

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (1)

2.Remove Slave Valve.

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (2)

3.Remove Interlock parts (Pin, Spring, and Sleeve).

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (3)

4.From the Shift Bar Housing rim, remove the Retaining Cap Screws.
5.To break the Gasket seal, jar the Shift Bar Housing.

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (4)

6.Remove the Shift Bar Housing.
7.Inspect the Roll Pin, replace if damaged.
8.Remove the Gasket and clean all mounting surfaces of gasket material.

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (5)

9.If the three (3) sets of Tension Springs and Balls from the Housing top Bores are loose, tilt the Assembly and remove them.

How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission (6)

More repair case for Eaton,please refer to:Eaton Transmission Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Remove the Shift Bar Housing for Eaton Fuller Heavy Duty Transmission From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Get Approval Password for CNH EST Programming
Next: Next: How to Replace Battery for Volvo EC18 Electric Excavator

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2