Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Remove Instrument Cluster for Mercedes Benz W204

Posted on February 24, 2019 by VCDS

The instrument cluster on the Mercedes W204 is a single sealed unit with a single wiring connection on the back of it. While complete diagnosis of problems with the cluster are beyond the scope of this article it will show you how to remove the console if you need to replace it or send it out for repairs.

 

Applies to: C350 (2007-14), C180 (2007-14), C200 (2007-14), C230 (2007-14), C250 (2007-14), C280 (2007-14), C300 (2007-14), C320 (2007-14)

 

Time: 1 hour

Tab: $1600

Talent: 2

Tools: Trim removal tool, T20 Torx

Hot Tip: Remove the cluster carefully

Performance Gain: Working instrument

Complementary Modification: Detail the interior

 

Procedures:

Begin by moving the steering wheel as far back (yellow arrow) and as low as it will go (red arrow).If you have a power adjustment there is a lever on the bottom of the column you can use to move it.

How to Remove Instrument Cluster for Mercedes Benz W204

There is a single trim piece that surrounds the front of the instrument cluster (red arrow).Use care when removing it as some of the clips are small.

How to Remove Instrument Cluster for Mercedes Benz W204

Use you r trim removal too and gently pry the top of the trim piece downwards and out while pulling it out from the sides.There are two small clips that sit in the vent (red arrow).Use care when pulling these out as they are small and can break.

How to Remove Instrument Cluster for Mercedes Benz W204

Remove the trim piece from the top (red arrow)

How to Remove Instrument Cluster for Mercedes Benz W204

Remove the odometer reset by pulling it straight out.

How to Remove Instrument Cluster for Mercedes Benz W204

Use a long handled T20 Torx and remove the four Torx screws (red arrows) holding the cluster in the dash.

How to Remove Instrument Cluster for Mercedes Benz W204

Over the years the sun and gravity will cause the dash to settle.Take your time and carefully remove the cluster from the dash by tilting it down from the top and then removing it.

How to Remove Instrument Cluster for Mercedes Benz W204

There is a single electrical connection on the back of the cluster on the left side.Push in the tab on the back (red arrow),and slide the gray hinge upwards.

How to Remove Instrument Cluster for Mercedes Benz W204

This will push the connector out from the cluster.

How to Remove Instrument Cluster for Mercedes Benz W204

You can now remove the cluster from between the top of the steering wheel and dash.Installation is the reverse of removal.

How to Remove Instrument Cluster for Mercedes Benz W204

Done!

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Remove Instrument Cluster for Mercedes Benz W204 From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Replace Benz W204 Engine Oil Filter
Next: Next: Delphi DS150E Perform Injector Coding for Seat IBIZA 1.6TDI

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Caterpillar C9 Engine Coolant Level Signal Invalid Fault Code 12 111-2
  • chinaobd2.com Spring Festival Sale: Global Save Up to 50%
  • Allison 3000 & 4000 Gen5 Fault Code P070C Transmission Fluid Level Sensor Circuit Low
  • Allison 3000 & 4000 Gen5 Fault Code P070C Transmission Fluid Level Sensor Circuit Low
  • Doosan Machine Fault Code P060B ADC Test Error Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • pcb assembly
©2025 OBD2 Scanner Blog | Powered by Superb Themes