Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Remove & Install EMS Module for Scania C/K Series Truck

Posted on April 3, 2023April 3, 2023 by VCDS
How-to-Remove-Install-EMS-Module-for-Scania-CK-Series-Truck-5

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

The engine management system for Scania Euro 6 gas engines uses 3 interacting engine control units which communicate via the CAN network.If a fault occurs in the engine management system, the engine control unit sends information about this via the coordinator to the instrument cluster. A warning lamp in the instrument cluster comes on. Depending on the type of fault, some engine functions may be limited or the engine may be switched off.

 

In this instruction chinaobd2.com show you guide on how to remove and install EMS module for Scania C/K series truck.For more information about Scania truck,please refer to:Scania Trouble Repair.

 

Related Contents:

2022 Scania SDP3 V2.53.2 V2.40 Diagnostic Software Free Download

2021 2018 Scania Multi EPC Parts Catalogue Free Download

 

IMPORTANT!

Unlocking the engine control unit using SDP3.

You always need to take this action if the engine control unit is to be removed from the vehicle and then reused in another vehicle or together with another coordinator. During unlocking the engine control unit is reset to the unlocked status.

 

Procedures:

Initial work

1.Unlock the engine control unit using SDP3.

2.Open the hatch marked in the illustration.

How-to-Remove-Install-EMS-Module-for-Scania-CK-Series-Truck-1

3.IMPORTANT!

Always cut the main power before starting the work.

Switch off the power.

Remove the connection to the negative terminal on the battery or set the battery master switch to position OFF.

If it is necessary to lift the vehicle to access the control units, follow steps 4-6.

How-to-Remove-Install-EMS-Module-for-Scania-CK-Series-Truck-2

 

4.WARNING!

Always support the vehicle on stands when working on vehicles with air suspension. Empty the air bellows.

When working on vehicles without stands under the frame, there is a considerable risk of serious personal injury. When the bellows lose air pressure, the frame will drop onto the axles. This will occur when:

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Remove & Install EMS Module for Scania C/K Series Truck From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat DP3 Scania SDP3 SDP3

Post navigation

Prev: Prev: JCB Equipment K4716 Intake Pressure Sensor Signal is not Plausible Repair
Next: Next: EGR System Pressure Testing for Scania C,K Series Truck

Related Posts

BMW 35160 & 35080 EEPROM Odometer Correction By Yanhua 35xx Emulator

BMW 35160 & 35080 EEPROM Odometer Correction By Yanhua 35xx Emulator

2019.02.24

What’s the Features Of SmartPRO 5000U-Plus Programmer

What’s the Features Of SmartPRO 5000U-Plus Programmer

2023.06.10

How to Configure/Setup Adapter for Volvo PTT Premium Tech Tool

How to Configure/Setup Adapter for Volvo PTT Premium Tech Tool

2019.03.18

Iveco EASY 11.1.5 Software Free Download

Iveco EASY 11.1.5 Software Free Download

2019.03.27

Diamond Logic

Diamond Logic

2019.06.10

Newest XPROG v5.84 Software Free Download

Newest XPROG v5.84 Software Free Download

2019.08.7

Scania SDP3 V2.64.3 Download link

Scania SDP3 V2.64.3 Download link

2025.03.27

Newest Super SBB2 Key Programmer Oil/service Reset/TPMS/EPS/BMS Handheld Scanner

Newest Super SBB2 Key Programmer Oil/service Reset/TPMS/EPS/BMS Handheld Scanner

2018.12.17

SsangYong EPC Parts Catalog Free Download

SsangYong EPC Parts Catalog Free Download

2019.07.26

Xhorse Dolphin XP005 vs. XP007 Key Cutting Machine

Xhorse Dolphin XP005 vs. XP007 Key Cutting Machine

2019.12.26

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Scania Truck Direction Indicator Front Right CUV 5 Trouble Repair
  • How to Solve CAT C9 Engine 8 Volt Supply Voltage High Problem
  • How to Replace HV Battery ECU for HINO Truck J05E Engine
  • Scania Truck CAN Communicatinon Fault Engine Control Unit Error Solution
  • Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2