Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Remove and Install Oil Filter Base for Perkins 800D Series Engine

Posted on February 3, 2025 by
How to Remove and Install Oil Filter Base for Perkins 800D Series Engine (2)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to remove and install oil filter base for Perkins 800D series engine.

Related Contents:

Perkins EST 2024A & 2023A & 2019A Software Free Download

Perkins SPI2 2018A EPC+Service Manual Free Download

Removal Procedure

How to Remove and Install Oil Filter Base for Perkins 800D Series Engine (1)

1 Use Tooling (A) to remove engine oil filter (6) from engine oil filter base (5). Refer to Operation

and Maintenance Manual, “Engine Oil and Filter- Change”.

2 Mark the orientation of engine oil filter base (5) for installation. Remove bolt (2).

Note: The engine oil filter base can be oriented in different positions.

3 Remove bolt (4) and remove engine oil filter base (5) from the cylinder block. Plug the oil galleries in the cylinder block with suitable plugs.

4 Remove O-ring seal (1) from engine oil filter base (5).

5 Remove O-ring seal (3) from bolt (4).

 

Installation Procedure

How to Remove and Install Oil Filter Base for Perkins 800D Series Engine (2)

1 Ensure that the engine oil filter base is clean and free from damage. Clean the mating surfaces of the cylinder block.

2 Install a new O-ring seal (1) to engine oil filter base (5). Install a new O-ring seal (3) to bolt (4).

3 Position engine oil filter base (5) against the cylinder block. Install bolt (4) finger tight.

4 Ensure the correct orientation of engine oil filter base (5). Install bolt (2) finger tight.

Note: The engine oil filter base can be oriented in different positions.

5 Tighten bolt (4) to a torque of 50 N·m (37 lb ft).

Tighten bolt (2) to a torque of 11 N·m (97 lb in).

6 Install a new engine oil filter (6). Refer to Operation and Maintenance Manual, “Engine Oil and Filter – Change” for the correct procedure.

More trouble repair case for Perkins,pls refer to:Perkins Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to Remove and Install Oil Filter Base for Perkins 800D Series Engine

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to Remove and Install Oil Filter Base for Perkins 800D Series Engine

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to Remove and Install Oil Filter Base for Perkins 800D Series Engine

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Toyota Previa MPV Smart Card All Keys Lost Programming Guide
How to Remove and Install Oil Filter Base for Perkins 800D Series Engine

Toyota Previa is an MPV produced by Toyota since 1990. It is called Estima (?????) in the Japanese market and Read more

This Post: How to Remove and Install Oil Filter Base for Perkins 800D Series Engine From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Detroit GHG17 Heavy Duty Engine Output Component Test Guide
Next: Next: Ford R7F7010643 (Encrypted) Airbag Repaired by CGDI CG100X

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit
  • How to Solve Caterpillar 24 PID 100-3 Oil Pressure Voltage High?

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2