Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Memorize & Active TPMS Sensors for Acura & Honda

Posted on February 24, 2019 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This article show a step-by step guide on how to memorize and active TPMS sensors for Acura & Honda.I am sorry for the text only without the pics,but it is easy to perform it.

How to Memorize & Active TPMS Sensors for Acura & Honda

Tools you need:

Autel TS401 TPMS Sensor Initializer Tool

Honda HDS Scan Tool (Honda HDS Software Download)

How to Install Honda HDS Software for DIY

Procedures:

Memorizing Sensor ID

1.This procedure must be performed at least 12 ft away from any other vehicle equipped tire pressure sensors.

2.Turn ignition off and wait about 5 minutes for TPMS sensors to enter sleep mode.Connect scan tool to vehicle data link connector.

3.Turn ignition on.

4.Verify scan tool communication with vehicle and TPMS control unit.

5.Select Sensor ID Learning from the mode menu on the scan tool.

6.Follow scan tool screen prompts to turn on sensor initializer tool. Verify that the power switch is in the low position.

7.Hold sensor initializer tool near any wheel; memorize sensor ID by following screen prompts on scan tool.

8.Repeat step 6 for each wheel until all 4 sensor IDs are memorized. The low tire pressure indicator will blink when all 4 IDs are memorized.

9.Turn ignition off.

10.Disconnect scan tool from vehicle.

11.Drive vehicle at a minimum speed of 28 mph for at least 1 minute.

12.Verify that low tire pressure indicator does not blink.

13.Turn ignition off.

14.Reduce pressure in one tire until it is less than vehicle specification.

15.Turn ignition on without starting vehicle.

16.Drive vehicle at a minimum speed of 28 mph for at least 1 minute.

17.Make sure the low tire pressure indicator turns on and inflate tires to vehicle specifications.

18.Repeat step 12 to 16 for all remaining tires.

19.Clear any DTCs with scan tool.

 

Sensor Location

1.With the ignition OFF, connect the HDS to the Data Link Connector (DLC) located under left side of the dashboard.

2.Turn ignition switch ON, and verify that HDS is communicating with the TPMS control unit.

3.Select

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to Memorize & Active TPMS Sensors for Acura & Honda

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to Memorize & Active TPMS Sensors for Acura & Honda

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to Memorize & Active TPMS Sensors for Acura & Honda

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Toyota Previa MPV Smart Card All Keys Lost Programming Guide
How to Memorize & Active TPMS Sensors for Acura & Honda

Toyota Previa is an MPV produced by Toyota since 1990. It is called Estima (?????) in the Japanese market and Read more

This Post: How to Memorize & Active TPMS Sensors for Acura & Honda From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Diesel Engine Control ECU Maps Analysis
Next: Next: How to Use WinOLS to Fix EDC16 Hot Start Problem

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2