Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Initialize Nissan TEANA Window and Sunroof Configuration

Posted on August 7, 2019August 7, 2019 by VCDS
How to Initialize Nissan TEANA Window and Sunroof Configuration

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

In this article www.chinaobd2.com will show you how to initialize window control module and sunroof for Nissan TEANA.And for more Nissan topic,check here:Nissan Trouble Repair

How to Initialize Nissan TEANA Window and Sunroof Configuration

How to Initialize Window Control Module for Nissan TEANA:

When Nissan TEANA battery power off or replace battery,replace window glass or replace window motor,you will find the auto window roll up to the top and it will down again.Now you need to initialize the window control module.But you will find the regular method can not work:hold on the widow up button when window up to top about 5 seconds.

1.Dissable the door panel,then remove widow glasses and window regulator assembly

2.Remove motor from assemble

3.Turn ignition,press window control switch down button about two or three times,the motor will rotate 3 turn briefly

4.Now press driver side control switch panel to roll up window,the motor will rotate,wait it stop,then turn ignition off.

5.Initialization complete,now install all part back.

Note:

Need to remove motor from window regulator assembly

This method apply to any window for Nissan TEANA

Nissan TEANA Electrical Sunroof Initialization Guide:

When you need to Initialize Sunroof

1.Battery dead when sunroof working

2.When you replace sunroof motor

3.After you perform emergency handle

4.Sunroof can not work correctly

Nissan TEANA Electrical Sunroof Procedures:

1.Hold on sunroof switch(close or up) about 10 seconds

2.The glass cover will move in the upward tilt direction and then mechanically stop, then will automatically close completely. After that, the glass cover will be operated in the order of

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Initialize Nissan TEANA Window and Sunroof Configuration From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: Car Key Programmer Code Reader ECU Chip Tunning gm iprog key Key Pro Nissan OBD2 original program Scania VCI vci wholesale

Post navigation

Prev: Prev: MAN MANTIS EPC Electronic Parts Catalogue Free Download
Next: Next: Newest XPROG v5.84 Software Free Download

Related Posts

Scania SDP3 2.58.3 free download Scania Diagnosis & Programming 3 download link

Scania SDP3 2.58.3 free download Scania Diagnosis & Programming 3 download ...

2024.02.16

Launch X431

Launch X431

2023.04.3

What is Vapon VP996 Auto Key Programmer

What is Vapon VP996 Auto Key Programmer

2023.04.2

QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

QSK60 G CM2358 Fault Code 1367 Pre-Oil Filter Pressure Sensor Circuit

2024.08.24

2019 Latest ATMEGA64 Repair Chip Update Software for XPROG-M Programmer V5.0/V5.3/V5.45/V5.50 to V5.84 Full Authorization (Including CAS4)

2019 Latest ATMEGA64 Repair Chip Update Software for XPROG-M Programmer V5.0/V5....

2019.02.26

Hitachi ZX890-7 Excavator Main Controller Removal Guide

Hitachi ZX890-7 Excavator Main Controller Removal Guide

2023.04.17

What is the Difference Between Ford IDS and FCOM

What is the Difference Between Ford IDS and FCOM

2019.05.31

Caterpillar ET 2018A Electronic Technician Software Free Download

Caterpillar ET 2018A Electronic Technician Software Free Download

2019.07.24

What are the functions of Iprog+ Programmer?

What are the functions of Iprog+ Programmer?

2019.04.26

How to Solve SVDI 2019 License Missing

How to Solve SVDI 2019 License Missing

2019.12.26

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution
  • Use Xhorse MLB Tool MQB48 Adapter and Key Tool Plus in 2 Methods

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2