Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Initialize Nissan TEANA Window and Sunroof Configuration

Posted on July 31, 2019July 31, 2019 by VCDS
How to Initialize Nissan TEANA Window and Sunroof Configuration

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

In this article www.chinaobd2.com will show you how to initialize window control module and sunroof for Nissan TEANA.And for more Nissan topic,check here:Nissan Trouble Repair

How to Initialize Nissan TEANA Window and Sunroof Configuration

How to Initialize Window Control Module for Nissan TEANA:

When Nissan TEANA battery power off or replace battery,replace window glass or replace window motor,you will find the auto window roll up to the top and it will down again.Now you need to initialize the window control module.But you will find the regular method can not work:hold on the widow up button when window up to top about 5 seconds.

1.Dissable the door panel,then remove widow glasses and window regulator assembly

2.Remove motor from assemble

3.Turn ignition,press window control switch down button about two or three times,the motor will rotate 3 turn briefly

4.Now press driver side control switch panel to roll up window,the motor will rotate,wait it stop,then turn ignition off.

5.Initialization complete,now install all part back.

Note:

Need to remove motor from window regulator assembly

This method apply to any window for Nissan TEANA

Nissan TEANA Electrical Sunroof Initialization Guide:

When you need to Initialize Sunroof

1.Battery dead when sunroof working

2.When you replace sunroof motor

3.After you perform emergency handle

4.Sunroof can not work correctly

Nissan TEANA Electrical Sunroof Procedures:

1.Hold on sunroof switch(close or up) about 10 seconds

2.The glass cover will move in the upward tilt direction and then mechanically stop, then will automatically close completely. After that, the glass cover will be operated in the order of

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
Original Handy Baby 2 II Key Programmer Hand-held Car Key Copy Key Programmer for 4D/46/48 Chips
How to Initialize Nissan TEANA Window and Sunroof Configuration

Handy Baby 2 II Key Programmer Hand-held Car Key Copy Key Programmer for 4D/46/48 ChipsNote: Language: English, SpanishThis Device can't work together Read more

Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1
Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1

Renault CAN Clip V175 and Consult 3 III For Nissan Professional Diagnostic Tool 2 in 1 Descriptions of Consult 3 Read more

Super VAG K+CAN V4.6 With Multi Language
Super VAG K+CAN V4.6 With Multi Language

Super VAG K+CAN V4.6 Top 3 Reasons To Get Super VAG: Software Version: V4.6Supported Languages: English/ Spanish/ Italian/ Portuguese/ GreekUDS Protocol Read more

CMD CAN Flasher V1251 Free Shipping
CMD CAN Flasher V1251 Free Shipping

CMD CAN Flasher V1251Supported VehiclesALFA ROMEO,147,1.9 JTD 110Kw EDC16C39,BOSCH EDC16+ C39 AlfaRomeo/Fiat/LanciaALFA ROMEO,147,1.9 JTD 16V EDC16C8,BOSCH EDC16 AlfaRomeo/Fiat/LanciaALFA ROMEO,147,1.9 JTD Read more

This Post: How to Initialize Nissan TEANA Window and Sunroof Configuration From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: Car Key Programmer Code Reader ECU Chip Tunning gm iprog key Key Pro Nissan OBD2 original program Scania VCI vci wholesale

Post navigation

Prev: Prev: How to do an Oil Change for Toyota Camry 2005-2010 by Yourself
Next: Next: MAN MANTIS EPC Electronic Parts Catalogue Free Download

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2