Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2

Posted on January 2, 2025 by
How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (5)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

The 4-series do not have a coordinator and uses VCI 1 to connect to the vehicle to run SD2/SP2. To read engine data in real time with for example XCOM you have to connect to CAN with VCI 2. To do that you need a “homemade” VCI-cable, see below, and a software-fix to connect to the
engine control unit (ECU).

Related Contents:

Scania XCOM v2.54 v2.30 v2.27 Dongle Emulator Free Download

Scania SDP3 2.63.2 Truck Diagnostic Software

It also works with DMecNet, CDev, Gadget and other SCOMM based programs.
1 You need:
Standard CAN connector (Scania P/N 1349719)
4 cables (approx. 40cm)
2 alligator clip
Standard VCI connector

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (1)

2 Connect the wires according to pictures
Pin 16 to red alligator clip
Pin 4 to black alligator clip
Pin 6 and 14 to CAN connector

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (2)

3 Set the tester address and search mode in XCOM
These changes will make XCOM, SDP3, Gadget, CDev and DMecNet to only scan for EMS on the CAN bus. No other ECUs will be found!
Open Options in XCOM (Options menu -> Options)

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (3)

Set Tester address to “F9”
Change search mode to “S6 PRESAMM (Physical request ECU 0x00)”. Select OK on the warning.
Press OK to accept changes.
Restart XCOM

4 Connect the “Homemade” VCI cable to the vehicle under the fuse box. Connect VCI2 to the VCI connection.

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (4)

5 Scania XCOM is now ready to connect to the EMS.
6 Restore XCOM
Revert the changes done in step 3 and restart XCOM. Tester address F9 is normal for XCOM. If another address were used previously, restore to that address instead.

How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 (5)

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to Configure XCOM to Scania 4 Series ECU EMS by VCI2

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to Configure XCOM to Scania 4 Series ECU EMS by VCI2

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to Configure XCOM to Scania 4 Series ECU EMS by VCI2

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
How to Configure XCOM to Scania 4 Series ECU EMS by VCI2

This article show a guide on how to use G-scan2

This Post: How to Configure XCOM to Scania 4 Series ECU EMS by VCI2 From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Motronic 1.7 Fiat ECU Pinout Component Diagram
Next: Next: Lonsdor K518 Pro OBD Cable VS Lonsdor DOIP Cable

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit
  • How to Solve Caterpillar 24 PID 100-3 Oil Pressure Voltage High?

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2