Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Posted on December 24, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Tutorial:

How to use Launch X431 ECU & TCU Programmer to clone BOSCH MED17.8.10 TC1728 ECU on bench?

Operation guide:

It’s easy to connect device and ECU according to the wiring diagram in the software, and then perform the read and write operations by selecting the corresponding function.

STEP 1.Connect device, PC and ECU

Connect X431 ECU Programmer to a computer via a USB cable

Open X-431 ECU & TCU Programmer software

Obtain the ECU model quickly by inputting med17.8.10 in the search box

Find the ECU is GreatWall Hover 62014-2018 TGI 1497 164 MED17.8.10 HW2_TC1728

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Double-click the ECU to enter the main operation interface

Follow the “Direct connection of diagram” to connect X-431 ECU Programmer and Bosch MED17.8.10 ECU with the BENCH mode line properly, and connect the power supply to the programmer as well

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

After connection, start to read and write ECU.

STEP 2.Read and save original Bosch MED17.8.10

Read chip ID>> Read and backup the original EEPROM data>> Read and backup the original Flash data>> Disconnect

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

STEP 3. Read and save new Bosch MED17.8.10

Connect Launch X431 ECU Programmer to a new MED17.8.10 ECU, repeat the same steps to read and save the new Bosch ECU data

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

STEP 4.Write original data to new ECU

Upload the corresponding original files to write into the new Bosch ECU

How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Done!

The operation guide also applies to LAUNCH X431 X-PROG3 with PC Adapter.

www.chinaobd2.com

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

UPA USB Programmer V1.3 Crack Software Free Download
How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer?

What is UPA USB Programmer? UPA USB Programmer

This Post: How to Clone Bosch MED17.8.10 TC1728 with Launch X431 ECU Programmer? From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: What is Xhorse Multi-Prog?
Next: Next: How to Clone Bosch ME17.8.8 with Launch X431 ECU Programmer on Bench?

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2