Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck

Posted on July 23, 2023 by
How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (8)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to check and adjust cylinder cutter for Scania C,K series truck.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (1)

 

Related Contents:

2022 Scania SDP3 V2.53.2 V2.40 Diagnostic Software Free Download

2023 2018 Scania Multi EPC Parts Catalogue Free Download

 

 

IMPORTANT!

Measure the lower cylinder liner diameter to make sure that the cylinder liner mounted in the cylinder block is 139 mm or 140 mm.

 

Procedures:

1 Check the fixture. Insert the gauge and check that the micrometer indicates 0.00 mm. The loose stop lug must be removed in order to use the gauge. Refit the loose stop lug after checking and adjusting if required.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (2)

2 Remove the hexagon socket screw in the centre of the cutting head.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (3)

3 Place the cutting head in the fixture. Centre the cutting head by turning it clockwise until it rests against the pin and the cutter stops against the loose stop lug.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (4)

4 If this value is correct, refit the cutting head on the tool and tighten the hexagon socket screw. If the value needs to be adjusted, proceed as follows:

  • Cylinder liner diameter 139 mm Check that the cutter is set so that the micrometer indicates 14.03 mm.
  • Cylinder liner diameter 140 mm Check that the cutter is set so that the micrometer indicates 15.03 mm.

 

5 Hold the cutter against the lug and undo the hexagon socket screw securing the cutter. The cutter is spring loaded.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (5)

6 Hold the cutting head with your hand and adjust the micrometer.

  • 14.03 mm gives the cutting head a diameter of 139.03 mm.
  • 15.03 mm gives the cutting head a diameter of 140.03 mm.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (6)

7 Lightly tighten the hexagon socket screw securing the cutter.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (7)

8 Back off the micrometer.

 

9 Tighten the hexagon socket screw securing the cutter.

How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck (8)

10 Check the value again.

 

11 Refit the cutting head on the tool, tighten the hexagon socket screw in the centre.

 

For more information about Scania truck,please refer to:Scania Trouble Repair.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Check and Adjust Cylinder Cutter for Scania C,K Series Truck From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: ISUZU 4LE2 Tier-4 Engine Injector Removal Guide
Next: Next: How to Use JPRO Commercial Vehicle 2023 Data Monitor Function

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Doosan Stage V Engine U02A2 Timeout Error of CAN-Receive-Frame A1DEFI Solution
  • What is “Unlock DME” for Yanhua ACDP BMW BDC2 All Keys Lost?
  • How to Solve Doosan Stage V Engine P011E Coolant Temperature Plausibility Fault
  • Xhorse VVDI2 V7.5.0 Update: Suport add key function for BMW G-Series BDC2 type
  • Yanhua ACDP2 Fixed BMW BDC2 System Abnormal and Coding Lost Issues

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2