Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

How to Bleed Air from Fuel System for Hitachi ZX890LCH-7 Excavator

Posted on April 2, 2023 by VCDS
How-to-Bleed-Air-from-Fuel-System-for-Hitachi-ZX890LCH-7-Excavator-4

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to bleed air from fuel system for Hitachi ZX890LCH-7 ZX890LCR-7.Air in the fuel system may make the engine hard to start or make it run irregularly. After draining water and sediment from the fuel filter,replacing the fuel filter element or running the fuel tank dry, be sure to bleed the air from the fuel system.

 

Related Contents:

Hitachi MPDr v2.56 v2.25 Diagnostic Software Free Download

Hitachi Excavator ZX-7 Service Repair Workshop Manual 2021

Hitachi Dr.ZX Excavator Diagnostic Tool Cable

 

IMPORTANT

Even if air is not thoroughly bled, do not hold the key switch in the ON position for more than five minutes continuously. If air is not thoroughly bled, first,return the key switch to the OFF position. Then, after waiting for more than 30 seconds, set the key switch to the ON position again. Failure to do so may cause damage to the fuel solenoid pump and/or discharging the batteries.

 

Check that fuel cock (1) near the fuel pre-filteris opened.

How-to-Bleed-Air-from-Fuel-System-for-Hitachi-ZX890LCH-7-Excavator-1

Set the key switch to the ON position and hold it in that position for approximately three minutes. The fuel solenoid pump operates and starts to bleed air.

 

 

CAUTION

Bleed air from fuel main filter(2) one side at a time. Loosen air bleed plug (3) on fuel main filter(2) while turning the key switch to the ON position. Run priming pump (4). When air is bled from fuel main filter(2), tighten air bleed plug (3). Return priming pump (4) to its original position.

 

Wipe offleaked fuel.

After fuel main filter(2) is filledwith fuel, hold the key switch in the ON position for 30 seconds.

How-to-Bleed-Air-from-Fuel-System-for-Hitachi-ZX890LCH-7-Excavator-2

Start the engine and check the fuel system for any fuel leakage.

 

Priming Pump Only

When a fault on the fuel solenoid pump or some other reason prevents air from being bled, air can be bled on only the priming pump.

Check that fuel cock (1) near the fuel pre-filteris opened.

How-to-Bleed-Air-from-Fuel-System-for-Hitachi-ZX890LCH-7-Excavator-3

 

Loosen air bleed plug (3) on fuel main filter(2).:10 mm

Run priming pump (4), and supply fuel. When air bubbles no longer come out, tighten air bleed plug (3). : 10 mm

After tightening air bleed plug (3), run priming pump (4) approximately 150 times.

How-to-Bleed-Air-from-Fuel-System-for-Hitachi-ZX890LCH-7-Excavator-4

Wipe offleaked fuel.

Start the engine and check the fuel system for any fuel leakage.

 

If Air Mixed Downstream from Common Rail

If air becomes mixed into the fuel system of downstream from common rail, bleed air by following the procedure below.

According to the air bleeding procedures, bleed enough air up to the engine supply pump entrance.

Operate the starter motor for cranking within 20 seconds. If the engine fails to start at a time, wait about 60 seconds, then try again.

 

More repair cases for Hitachi excavator,please refer to:Hitachi Excavator Trouble Repair.

(Visited 9 times, 2 visits today)

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: How to Bleed Air from Fuel System for Hitachi ZX890LCH-7 Excavator From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Nissan Maxima 2012 93C66 Mileage Corrected by iPROG
Next: Next: Kobelco ISUZU 4JJ1 P0047 Turbocharger EVRV Control Circuit High Solution

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2