Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide

Posted on November 14, 2024 by
HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide (2)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to perform No load max differential pressure measurement for HITACHI ZX-5 excavator.

 

 

What You Need?

Hitachi Dr.ZX diagnostic Tool

Hitachi AllinOne MPDr v3.32 v2.25 2021 Diagnostic Software Free Download

 

 

Measurement of No Load Max differential pressure can be done.
When the fault code of ECM muffler filter PM Over-Restriction is displayed, check the muffler filter condition by measuring

No Load Max differential pressure.
Check the muffler filter condition.
Refer to the Technical Manual (Troubleshooting).
1. Click the [[F] No Load Max Differential Pressure Measurement] button.
HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide (1)

2.Measure the differential pressure by following the procedure displayed on the monitor screen.

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide (2)

 

Step 1: Warm the engine.

Raise the boom and relief at arm crowd end. Bring the Coolant Temperature to

70 deg.C or more,the MF Filter Inlet Temperature to 200 deg.C or more.

 

Step 2:

Turn the engine control dial to LOW.

Raise the Pilot Control Shut-Off Lever.

Turn OFF Auto Idle.

Turn OFF Auto Shut-Down.

 

Step 3:

Wait until the MF Filter Inlet Temperature is 140 deg.C or less.

 

Step 4:

Bring the Actual Engine Speed to 1700min-1.Wait until the MF Filter Inlet

Temperature is 150 deg.C or more

 

Completion:

The measurement task is now complete.

Return Auto Idle. Auto Shut-Down and Power Mode switching settings to the original. This completes the task.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to Solve Perkins 1106D EPG Engine E398 Low Fuel Rail Pressure Error
Next: Next: How to Solve Doosan Machine P02EB Over Temperature Error

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • ECUDESK Software Latest ECU Support List (2025.05)
  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2