Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block

Posted on June 11, 2024 by
HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (8)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Location of the Cab Side
The fuse block and the relay panel are located inside the instrument panel as shown below.

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (1) HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (2)

 

[NOTE]
Be sure to use each capacity fuse designated in the above table.
Never use the capacity fuse exceeding the designated one in the above, otherwise over current may damage the harness wires and fusible linkage wires.

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (3)

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (4)

 

 

Related Contents:

Nexiq USB Link

2024.02 HINO Diagnostic Explorer DX3/DX2 Diagnostic Software Free Download

HINO Trucks EPC Electronic Parts Catalog 2018?2016 Free Download

 

 

Location of the Chassis Side
The fusible link block is installed in left side rail as shown below

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (5)

[NOTE]
Do not remove the harness connector, fusible link block, and cover except for repair and/or inspection.
If removal is necessary, pay attention that water and/or foreign matter do not attach or enter
the connector, terminals, electric component box, and cover.
If repair or replacement is required, make sure there is no attachment or entry of water and/or
foreign matter. Mount properly to ensure waterproof function is not compromised.

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (6)

 

DETAIL OF FUSIBLE LINK AND RELAY POSITION

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (7)

  • How to remove fusible link box cover.
    1. Push lock lever and remove lock. (2 position, marked )
    2. Pull-up 2 position of plate lock (marked ) and remove cover.

HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block (8)

More case for HINO please refer to:HINO Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Mini R56 Misfire Abnormal Vibration Diagnosis & Repair by G-scan2
HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block

This article show a guide on how to use G-scan2

This Post: HINO L-Series Truck Fuse Block Relay Panel and Fusible Link Block From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: MAN Truck Idle Speed Adjustment by Launch X431
Next: Next: CLAAS Lexion 480 Combine Reverser Drive Removal Guide

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2