Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation
How to use CGDI CG100X Programmer to repair encrypted Renesas R7F7010643 Ford airbag?
Check the step-by-step guide below.
Model Info:
Vehicle: Ford Focus 2023
Restraint Control Module (RCM) Part Number: RJ7T-14B321-AB
Processor: Renesas R7F7010643 (Encrypted)
Main steps:
Step 1: Diagnose Airbag Module by CGDI CG70
Step 2: Repair Airbag with CGDI CG100X
Step 3: Verify the Repair by CG70
Make sure the CG100X software is V1.6.2.1 or above.
It can support Ford LV4T-14B321-XA R7F701A033 (encrypted), Ford RJ7T-14B321-AB R7F7010643 (encrypted), Ford LK9T-14B321-AA R7F7010643 (encrypted), and Ford MZ8T-14B321-AA R7F7010643 (encrypted) airbag repair.
In detail…
Step 1: Diagnose Airbag Module by CGDI CG70
1.Read SRS Fault Codes
Use the CG70 airbag reset tool or a diagnostic scanner.
Run CG70 software, select Ford and the appropriate part number. The software will display the wiring diagram.
Follow the diagram to connect CG70 tool to the airbag module (need to connect the GND, CANL, CANH and 12V cables)
Read the fault code successfully
2.Identify the Crash Data Issue
If fault code B1193 – Crash Event Storage Full and Locked appears, it indicates crash data is stored in the airbag control module (ACM/SDM).
This fault cannot be cleared with diagnostic tools, as it gives the error: “Cannot execute routine.”
Solution: Use the CG100X programmer to erase the crash data.
Step 2: Repair Airbag with CGDI CG100X
1.Understand Compatibility
CG70 cannot handle the encrypted R7F7010643 processor.
CG100X can decrypt and erase the crash data.
Note: OBDSTAR P50 can only diagnose this issue but cannot erase the crash.
2.Prepare the Setup
Run CG100X software, select Ford, and search for the part number. The software will display the wiring diagram.
Pay attention to the wiring setup.
3.Wiring Requirements
Remove one capacitor from the airbag module’s mainboard.
Use the following:
CG100X D1 Adapter
2mm Thin Cable
10 kΩ Resistor
Important: Be cautious when desoldering the capacitor as it is very small.
4.Connect the Module
Use the D1 adapter to connect the SRS module and CG100X
Ensure the 5.10 kΩ resistor does not touch the board to avoid short circuits or communication failures.
5.Decrypt and Read Data
Begin decrypting the chip.
Read the chip’s DFlash and PFlash, and then save the data.
6.Repair Airbag Data
Confirm to repair the airbag data when prompted.
Write the repaired data back to the chip
Erase the crash data and repair the SRS module successfully now.
7.Recover Airbag Module
Disconnect all wires from the CG100X Programmer.
Re-solder the capacitor back onto the airbag module’s mainboard.
Step 3: Verify the Repair by CG70
Connect the airbag module back to the CGDI CG70 airbag reset tool.
Read the fault codes to ensure no crash data is stored.
Done!
www.chinaobd2.com
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: adapter airbag repair cat CGDI Ford program
Related Posts
How to Use ECUsafe EGR/DPF/FAP Removal Software
2019.02.24
Five reasons why programmer chip programming is unstable
2023.06.4
Cummins inline 5 insite 7.5 USB serial port COM2 and FAQ
2022.07.20
BMW X5 X6 N55 Valvetronic Transmission Malfunction Trouble Repair
2020.10.11
Program Honda Accord 2021 All Keys Lost by Autel KM100
2024.01.28
Jpro Toolbar Perform a Comprehensive Electronic Inspection With Visual PM Inspec...
2024.01.28
How to do odometer correction for Toyota by Iprog+ Programmer
2024.01.28
Scania VCI3 SDP3 software error Solution
2019.12.15
How to do BMW engine re-adaptation using ISTA D or ISTA+
2019.12.26
Yanhua Mini ACDP Adds CAS1-CAS4 Data Renew Function
2019.03.8