Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Doosan ISUZU 6UZ1 Engine Lost Communication with TCM U0101 Solution

Posted on April 17, 2023April 17, 2023 by VCDS
doosan-dx170lc-5

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to diagnose and repair Doosan machine with ISUZU 6UZ1 INT-Tier 4 engine lost communication with TCM U0101 Flash code 85 error.

doosan-dx170lc-5

Related Contents:

ISUZU E-IDSS 2022 2019 Engine Diagnostic Service System Free Download

ISUZU IDSS Diagnostic Tool

 

Procedures:

1.Inspect the CAN-Low circuit and CAN-High circuit between the ECM and the control unit of the machine.

There should be no short to the battery or ignition power source.

There should not be an open circuit or high resistance.

There should be no short to GND.

 

2.If a problem is found, repair the CAN circuit.

3.If the CAN circuit is normal, connect all harnesses.

4.Clear the DTC using the trouble diagnosis scan tool.

5.Turn OFF the ignition switch for at least 30 seconds.

6.Perform a test-run.

7.Check the DTC.

8.If a DTC has been detected, replace the control unit of the machine.

9.Connect all harnesses.

10.Clear the DTC using the trouble diagnosis scan tool.

11.Turn OFF the ignition switch for at least 30 seconds.

12.Perform a test-run.

13.Check the DTC.

14.If a DTC has been detected, replace the ECM.

15.Set the Injector ID Code and engine No. on the ECM.

 

2.U0101 Confirm Resolution

Clear the DTC using the trouble diagnosis scan tool.

Turn OFF the ignition switch for at least 30 seconds.

Start the engine.

Perform a test-run.

Use the trouble diagnosis scan tool to confirm that a DTC has not been detected.

More repair cases for ISUZU engine,please refer to:ISUZU Engine Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Doosan ISUZU 6UZ1 Engine Lost Communication with TCM U0101 Solution From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat

Post navigation

Prev: Prev: Hitachi ZX890-7 Excavator Main Controller Removal Guide
Next: Next: How to Use Autel KM100 Program New Key for BMW 1 Series 2010-2016

Related Posts

Toyota Corolla 2013+ Keyless Go All Keys Lost Programming by Zed-Full

Toyota Corolla 2013+ Keyless Go All Keys Lost Programming by Zed-Full

2019.07.31

How to perform hydraulic pump pressure test for New Holland T6030 tractor

How to perform hydraulic pump pressure test for New Holland T6030 tractor

2024.01.28

What kinds of key cutting machine do you use?

What kinds of key cutting machine do you use?

2019.12.19

BMW X5 X6 N55 Valvetronic Transmission Malfunction Trouble Repair

BMW X5 X6 N55 Valvetronic Transmission Malfunction Trouble Repair

2020.10.11

Volkswagen Santana Vista 2012 All Key Lost Programming

Volkswagen Santana Vista 2012 All Key Lost Programming

2019.05.13

How to Access JLR SDD Engineering Mode (Seed Key)

How to Access JLR SDD Engineering Mode (Seed Key)

2023.04.4

Operation Steps for Vetronix Tech 2 GM Scanner

Operation Steps for Vetronix Tech 2 GM Scanner

2024.01.28

How to Install Scania VCI3 Diagnostic and Programming Software Scania SDP3

How to Install Scania VCI3 Diagnostic and Programming Software Scania SDP3

2019.12.15

How to solve VW 2004 Touareg airbag warning light on

How to solve VW 2004 Touareg airbag warning light on

2019.02.24

How to do BMW engine re-adaptation using ISTA D or ISTA+

How to do BMW engine re-adaptation using ISTA D or ISTA+

2019.12.26

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution
  • OBDSTAR ECU Flasher Software Gets a Major Upgrade in June 2025
  • How to Remove HV Battery Cooling FAN for HINO Truck with J05E Engine
  • How to Calculate BMW F/G Series by APPRO2 for Free?
  • ECUDESK Software ECU Support List Update (2025.07)

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2