Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Bobcat 3450 Utility Vehicle Fuel Injector Removal and Installation Guide

Posted on April 6, 2023April 6, 2023 by VCDS
Bobcat-3450-Utility-Vehicle-Fuel-Injector-Removal-and-Installation-Guide

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

This instruction show you guide on how to remove and install fuel injector for Bobcat 3450 utility vehicle.

 

Related Contents:

Bobcat Service Analyzer 90.00 89.06 Diagnostic Software Free Download

 

Procedures:

Warning:

Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or
death. Fluid leaks under pressure may not be visible. Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

 

Close any fuel valves in the fuel supply line.
Clean the area around the fuel injection pump and fuel injectors to keep contaminants from entering the engine or fuel system.
Remove the intake manifold / valve cover assembly.

Remove the high-pressure fuel injection lines as an assembly.

Bobcat-3450-Utility-Vehicle-Fuel-Injector-Removal-and-Installation-Guide

Remove nut (Item 1).

Remove the fuel return line (Item 2) and copper washer (Item 3) from the fuel injectors.

 

NOTE:The fuel injectors used on IDI engines screw into the cylinder head.
Remove the fuel injectors (Item 4).
Remove the injector nozzle gaskets (Item 5) and protector (Item 6) from the cylinder head.

Installation
Insert the nozzle gaskets (Item 5) and nozzle protector (Item 6) in the cylinder head.
Install the fuel injector (Item 4) [Figure 50-70-26] in the cylinder head and tighten to specification.
Install new copper washers (Item 3) and high-pressure and return fuel lines (Item 2) Tighten fuel line nuts (Item 1) to 30

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Bobcat 3450 Utility Vehicle Fuel Injector Removal and Installation Guide From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Tags: cat

Post navigation

Prev: Prev: JCB Stage V Engine K4732 Intake Air Temperature Sensor Out of Range
Next: Next: Land Rover Sport 2016 New Key Programming by Autel IM608 Pro 2

Related Posts

Using a Diagnostic Car Code Reader You Don

Using a Diagnostic Car Code Reader You Don

2019.02.27

How to Use FCOM PATS Function for Key Programming

How to Use FCOM PATS Function for Key Programming

2019.06.10

SmartPRO 5000U-PLUS 5000u Plus Universal USB Programmer PCF29XX Chips Support List

SmartPRO 5000U-PLUS 5000u Plus Universal USB Programmer PCF29XX Chips Support Li...

2023.06.7

Mercede Benz MB diagnostic tool reviews and comparison

Mercede Benz MB diagnostic tool reviews and comparison

2020.01.3

How to make Xentry Passthru 12.2018 work with Actia XS 2G

How to make Xentry Passthru 12.2018 work with Actia XS 2G

2019.03.13

Mercedes Benz E-class New Key Adding by Autel IM608 Pro 2

Mercedes Benz E-class New Key Adding by Autel IM608 Pro 2

2023.04.20

Launch X431 Perform ECU Coding for VW Models

Launch X431 Perform ECU Coding for VW Models

2019.03.8

LISHI BW9MH 2 in1 Auto Pick and Decoder for BMW Motorcycle Tool

LISHI BW9MH 2 in1 Auto Pick and Decoder for BMW Motorcycle Tool

2018.12.17

Car keyless entry and start system solution based on NXP products

Car keyless entry and start system solution based on NXP products

2023.06.4

WiTech MicroPod 2 Customer Questions & Answers

WiTech MicroPod 2 Customer Questions & Answers

2024.01.28

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2